Poulan 96192003501, 429884 owner manual Storage, Other, Fuel System, Engine OIL, Cylinder

Page 19

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo Control Snow Discharge See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes 23 22 KEY Part Description Scrapper BAR Auger HousingAuger Assembly 30 LH Auger Assembly 30 RHBearing Plug Auger BearingDeflector Spring Knob BlackPOP Rivet Shoulder ScrewRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Tube Repair Parts Snow Thrower Model XT11530ES HandlesLoop Handle LH Loop Handle RHRetainer 180480Impeller ROD Traction RODWasher 3/8 SpacerKnob RED Handle KnobTorsion Spring Wire HarnessInterlock Spring Interlock CAMRepair Parts Snow Thrower Model XT11530ES Drive Rubber Ring AssemblyDrive Plate Assembly Speed SelectorSprocket Axle ShaftEngine Mounting Plate Engine ModelFrame 423185X505428684 Repair Parts Snow Thrower Model XT11530ES Wheels 01.06.005-A Safety Ignition KEY Repair Parts Snow Thrower Model XT11530ES BAG of Parts193071 DECAL, DANGER, Deflector Repair Parts Snow Thrower Model XT11530ES Decals181037 DECAL, DangerService Notes Service Notes Service Notes Limited Warranty

429884, 96192003501 specifications

The Poulan 96192003501,429884 is a powerful and versatile tool designed for outdoor maintenance, particularly for those who require a robust chainsaw for various tasks. This model is engineered with performance and efficiency in mind, making it an ideal choice for both professional landscapers and homeowners looking to tackle yard work with ease.

One of the standout features of the Poulan 96192003501,429884 is its advanced engine technology. The chainsaw is equipped with a reliable two-stroke engine that provides plenty of power for cutting through wood with minimal effort. This means users can expect quick and efficient performance, whether they are felling trees, trimming branches, or cutting firewood.

Safety is a top priority in the design of this chainsaw. It features an automatic chain oiler, ensuring the chain remains well-lubricated during operation, which not only prolongs the life of the chain but also reduces friction and heat buildup. Additionally, the Poulan chainsaw incorporates a low kickback chain, designed to minimize the risk of kickback during cutting, making it safer for users, especially beginners.

The Poulan 96192003501,429884 is also designed for user comfort. It features an ergonomic handle that offers a comfortable grip, reducing fatigue during extended use. The chainsaw's lightweight design enhances portability, allowing users to maneuver it easily in various environments, from dense woods to open fields.

Another notable characteristic is its easy-start technology. With this feature, starting the chainsaw is straightforward, requiring less effort to get the engine running smoothly. This convenience is particularly beneficial for those who may struggle with traditional starting mechanisms.

In summary, the Poulan 96192003501,429884 is a highly functional chainsaw that combines power, safety, and user-friendly features. Its advanced engine technology, automatic chain oiler, low kickback chain, ergonomic design, and easy-start capabilities make it an excellent choice for those looking to maintain their outdoor spaces efficiently and safely. Whether for professional landscaping or home improvement projects, this chainsaw stands out as a reliable tool for tackling a variety of cutting tasks.
Top Page Image Contents