Poulan 96192003501, 429884 owner manual Engine, Cleaning

Page 15

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo Control Snow Discharge See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes 23 22 KEY Part Description Scrapper BAR Auger HousingAuger Assembly 30 LH Auger Assembly 30 RHBearing Plug Auger BearingDeflector Spring Knob BlackPOP Rivet Shoulder ScrewRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Tube Repair Parts Snow Thrower Model XT11530ES HandlesLoop Handle LH Loop Handle RHRetainer 180480Impeller ROD Traction RODWasher 3/8 SpacerKnob RED Handle KnobTorsion Spring Wire HarnessInterlock Spring Interlock CAMRepair Parts Snow Thrower Model XT11530ES Drive Rubber Ring AssemblyDrive Plate Assembly Speed SelectorSprocket Axle ShaftEngine Mounting Plate Engine ModelFrame 423185X505428684 Repair Parts Snow Thrower Model XT11530ES Wheels 01.06.005-A Repair Parts Snow Thrower Model XT11530ES BAG of Parts Safety Ignition KEY193071 DECAL, DANGER, Deflector Repair Parts Snow Thrower Model XT11530ES Decals181037 DECAL, DangerService Notes Service Notes Service Notes Limited Warranty

429884, 96192003501 specifications

The Poulan 96192003501,429884 is a powerful and versatile tool designed for outdoor maintenance, particularly for those who require a robust chainsaw for various tasks. This model is engineered with performance and efficiency in mind, making it an ideal choice for both professional landscapers and homeowners looking to tackle yard work with ease.

One of the standout features of the Poulan 96192003501,429884 is its advanced engine technology. The chainsaw is equipped with a reliable two-stroke engine that provides plenty of power for cutting through wood with minimal effort. This means users can expect quick and efficient performance, whether they are felling trees, trimming branches, or cutting firewood.

Safety is a top priority in the design of this chainsaw. It features an automatic chain oiler, ensuring the chain remains well-lubricated during operation, which not only prolongs the life of the chain but also reduces friction and heat buildup. Additionally, the Poulan chainsaw incorporates a low kickback chain, designed to minimize the risk of kickback during cutting, making it safer for users, especially beginners.

The Poulan 96192003501,429884 is also designed for user comfort. It features an ergonomic handle that offers a comfortable grip, reducing fatigue during extended use. The chainsaw's lightweight design enhances portability, allowing users to maneuver it easily in various environments, from dense woods to open fields.

Another notable characteristic is its easy-start technology. With this feature, starting the chainsaw is straightforward, requiring less effort to get the engine running smoothly. This convenience is particularly beneficial for those who may struggle with traditional starting mechanisms.

In summary, the Poulan 96192003501,429884 is a highly functional chainsaw that combines power, safety, and user-friendly features. Its advanced engine technology, automatic chain oiler, low kickback chain, ergonomic design, and easy-start capabilities make it an excellent choice for those looking to maintain their outdoor spaces efficiently and safely. Whether for professional landscaping or home improvement projects, this chainsaw stands out as a reliable tool for tackling a variety of cutting tasks.
Top Page Image Contents