Poulan 430429, 96198002801 owner manual Safe Operation Practices for Walk-Behind Snow Throwers

Page 2

IMPORTANT

Safe Operation Practices for Walk-Behind Snow Throwers

This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury.

Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in order to prevent acci- dental starting when setting up, trans- porting, adjusting or making repairs.

WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping sur- faces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings.

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemi- cals known to the State of California to cause cancer and birth defects or other reproductive harm.

Training

1.Read, understand and follow all instructions on the machine and in the manual(s) before operating this unit. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

2.Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction.

3.Keep the area of operation clear of all persons, par- ticularly small children.

4.Exercise caution to avoid slipping or falling, especially when operating the snow thrower in reverse.

Preparation

1.Thoroughly inspect the area where the equipment is to be used and remove all doormats, sleds, boards, wires, and other foreign objects.

2.Disengage all clutches and shift into neutral before starting the engine (motor).

3.Do not operate the equipment without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear footwear that will improve footing on slippery surfaces.

4.Handle fuel with care; it is highly flammable

(a)Use an approved fuel container.

(b)Never add fuel to a running engine or hot en- gine.

(c)Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

(d)Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place contain- ers on the ground, away from your vehicle, before filling.

(e)When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

(f)Keep the nozzle in contact with the rim of the fuel tank or container opening at all times, until refuel- ing is complete. Do not use a nozzle lock-open device.

(g)Replace gasoline cap securely and wipe up spilled fuel.

(h)If fuel is spilled on clothing, change clothing im- mediately.

5.Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors or electric starting motors.

6.Adjust the collector housing height to clear gravel or crushed rock surface.

7.Never attempt to make any adjustments while the engine (motor) is running (except when specifically recommended by manufacturer).

8.Always wear safety glasses or eye shields during op- eration or while performing an adjustment or repair to protect eyes from foreign objects that may be thrown from the machine.

Operation

1.Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

2.Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

3.After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, disconnect the cord on electric motors, thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

4.If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

5.Stop the engine (motor) whenever you leave the oper- ating position, before unclogging the collector/impeller

 

housing or discharge chute, and when making any

2

repairs, adjustments or inspections.

 

Image 2
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine To Start EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Scraper BAR Auger HousingKEY Part Description Auger 27 LH23 22 KEY Part NO. NO. Description Auger Bearing Bearing PlugChute Weldment Deflector Control AssemblyDeflector Spring 15 420679 Service Part Deflector Control Deflector WeldmentCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Tube Loop Handle LHLoop Handle RH Pivot SupportKnob RED SpacerRetainer Handle KnobShifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomTorsion Spring Interlock SpringInterlock CAM Interlock StopSprocket Axle ShaftRoll PIN 3/16 Clik PINExploded Speed Selector AssemblyDrive Plate Assembly Rubber RingEngine Mounting Plate Frame427928X428 428685Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley187865X421 Wheel Assembly LH187833X421 KEY Part NO. no Safety Ignition KEY428498 DECAL, DANGER, Deflector 181037DECAL, Danger KEY Part Description QTY Warranty MANUFACTURER’S Warranty CoverageII. Emission Control System Warranty Warranty Limited Warranty