Poulan 96198002801, 430429 owner manual Meets A.N.S.I. Safety Requirements

Page 9

OPERATION

GASOLINE FILLER CAP

PRIMER

CHOKE

CON-

TROL

SAFETY

IGNITION KEY

FUEL SHUT-OFF VALVE

THROTTLE

RECOIL (AUXILIARY) STARTER HANDLE

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY

VARY WITH THE

ENGINE ON YOUR

UNIT.

AUGERS

POWER

 

 

 

CORD

AUGER

DISCHARGE CHUTE CONTROL LEVER

PLUG

CONTROL

 

LEVER

 

DEFLECTOR REMOTE

 

DRIVE SPEED

 

CONTROL LEVER

ELECTRIC

CONTROL LEVER

 

 

 

 

START

 

 

 

BUTTON

 

 

TRACTION

 

CHUTE

 

 

 

DRIVE

DEFLECTOR

 

 

CONTROL

 

 

 

 

 

 

LEVER

DISCHARGE

LIGHT

CHUTE

 

CLEAN-OUT TOOL

HANDLE

 

KNOB

 

MUFFLER

 

TOOLBOX

SKID PLATE

FIG. 10

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Throttle- used to select FAST or SLOW engine speeds. Choke Control - used for starting a cold engine.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power- propelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the direc- tion the snow is thrown.

Deflector remote control lever - used to change the distance the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

9

Image 9
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig To Start Engine Before Starting the EngineSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting KEY Part Description Auger HousingScraper BAR Auger 27 LH23 22 KEY Part NO. NO. Description Bearing Plug Auger BearingDeflector Spring 15 420679 Service Part Deflector Control Deflector Control AssemblyChute Weldment Deflector WeldmentCable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator HeadLoop Handle RH Loop Handle LHLower Tube Pivot SupportRetainer SpacerKnob RED Handle KnobTraction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomInterlock CAM Interlock SpringTorsion Spring Interlock StopRoll PIN 3/16 Axle ShaftSprocket Clik PINExploded Drive Plate Assembly AssemblySpeed Selector Rubber Ring427928X428 FrameEngine Mounting Plate 428685Traction Belt Impeller BeltIdler ARM Bracket Idler PulleyWheel Assembly LH 187833X421187865X421 Safety Ignition KEY 428498KEY Part NO. no 181037 DECAL, DangerDECAL, DANGER, Deflector KEY Part Description QTY MANUFACTURER’S Warranty Coverage WarrantyII. Emission Control System Warranty Warranty Limited Warranty