Poulan 96198002801 Impeller Belt, Traction Belt, Idler ARM Bracket, Idler Pulley, Idler Bracket

Page 35

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

CHASSIS / ENGINE / PULLEYS

23 22		13 21
24		13 21
		20
13 21		19
15		20
15			18
			18
11				17
				17
12				16
13	14			16
13	14
		7
	5
9
			4	6
		3	4	1
10		3		1
10				2
			8

			01.21.005-C
KEY	PART	DESCRIPTION	KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION	NO.	NO.	DESCRIPTION
1	419888	IMPELLER BELT	13	59289	WASHER
2	427304	TRACTION BELT	14	73800500	NUT 5/16-18
3	423723X479	IDLER ARM BRACKET	15	74780520	SCREW 5/16-18 X 1.25
4	180523	IDLER PULLEY	16	851084	SCREW 3/8-24 X 1.375
5	423990X479	IDLER BRACKET	17	19132005	WASHER
6	426589	NUT 5/16-18	18	425934	PULLEY ENG IMPELLER
7	74780524	SCREW 5/16-18 X 1.50	19	425933	PULLEY ENG TRACTION
8	424297	SHOULDER BOLT 5/16-18 X .50	20	74610516	SCREW 5/16-24 X 1.00
9	751153	NUT 5/16-18 NYLOCK	21	10040500	LOCKWASHER 5/16
10	428867	SCREW 5/16-18 X .625	22	155452	BELT GUIDE
11	427576	TRACTION IDLER BRACKET	23	11050500	LOCKWASHER 5/16
12	180522	TRACTION PULLEY	24	175331	IDLER BUSHING

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

35

Image 35

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Auger 27 LH Auger HousingKEY Part Description Scraper BAR23 22 KEY Part NO. NO. Description Bearing Plug Auger BearingDeflector Weldment Deflector Control AssemblyDeflector Spring 15 420679 Service Part Deflector Control Chute WeldmentRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldPivot Support Loop Handle LHLoop Handle RH Lower TubeHandle Knob SpacerRetainer Knob REDShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPInterlock Stop Interlock SpringInterlock CAM Torsion SpringClik PIN Axle ShaftRoll PIN 3/16 SprocketExploded Rubber Ring AssemblyDrive Plate Assembly Speed Selector428685 Frame427928X428 Engine Mounting PlateIdler Pulley Impeller BeltTraction Belt Idler ARM Bracket187865X421 Wheel Assembly LH187833X421 KEY Part NO. no Safety Ignition KEY428498 DECAL, DANGER, Deflector 181037DECAL, Danger KEY Part Description QTY MANUFACTURER’S Warranty Coverage WarrantyII. Emission Control System Warranty Warranty Limited Warranty