Poulan 418962 owner manual Engine, Cleaning

Page 14

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug Place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug Place wire where it cannot come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYDischarge chute control lever used to change the di Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting HOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Check Engine OIL Level See Fig Before Starting the EngineScraper BAR ADD Gasoline See FigIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Storage OtherTroubleshooting Service Notes AIG plugr1 KEY Part Description 07Chute-knob2 414280 Knob, Lever Repair Parts Snow Thrower - Model NO. PR5524ES Handles Repair Parts Snow Thrower - Model NO. PR5524ES Handles Repair Parts Snow Thrower - Model NO. PR5524ES KEY Part Description   402856X004 17490508403096X004 416717X004Page 181037 Decal, Danger 418962 418963Limited Warranty

418962 specifications

The Poulan 418962 is a powerful and versatile chainsaw designed for both professional landscapers and homeowners looking to tackle a variety of cutting tasks. With its robust design and advanced features, this chainsaw has garnered attention for its reliability and performance.

One of the standout features of the Poulan 418962 is its efficient engine. Powered by a 40cc, 2-cycle engine, it delivers significant power for cutting through different types of wood, including hardwoods and softwoods. The engine is designed with an easy-start feature, which allows for quick and effortless starting, reducing frustration during operation. This is particularly beneficial for users who need to make quick cuts without the hassle of extensive warm-up sessions.

The chainsaw also comes equipped with a 16-inch bar and chain, offering excellent cutting capacity while maintaining a lightweight design. This balance allows users to maneuver the saw easily, making it ideal for pruning trees, cutting firewood, or clearing fallen debris. The low-kickback design of the chain enhances safety, reducing the risk of injury during operation.

In terms of technology, the Poulan 418962 features an automatic chain lubrication system. This system ensures that the chain remains sufficiently lubricated while in use, extending its lifespan and improving cutting efficiency. Users can easily monitor the oil level through a transparent oil tank, making maintenance straightforward.

Another critical characteristic of this chainsaw is its ergonomic design. The comfortable handle provides a secure grip, reducing fatigue during prolonged use. This is especially useful for those who may be working on extensive cutting projects. Additionally, the chainsaw is designed to absorb vibrations, further enhancing user comfort.

Safety features are also a focal point of the Poulan 418962. It includes a chain brake that can quickly stop the chain in case of kickback, ensuring user protection. Furthermore, the rear handle is equipped with a trigger lockout, preventing accidental starts.

Overall, the Poulan 418962 stands out as a reliable and efficient tool, marrying power with user-friendly features. Its combination of an efficient engine, automatic lubrication, safety precautions, and ergonomic design makes it an excellent choice for anyone looking to invest in a quality chainsaw. Whether for occasional use or frequent tasks, the Poulan 418962 delivers performance and durability that users can count on.
Top Page Image Contents