Poulan 418962 owner manual Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 15

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure throttle is in STOP position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Remove safety ignition key and disconnect spark plug wire from spark plug Place wire where it cannot contact plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4.Connect spark plug wire to spark plug. Replace safety ignition key.

CHUTE DEFLECTOR

Thechutedeflector,attachedtothetopofthedischargechute, is provided to direct discharging snow away from the opera- tor. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 19)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shoulder/shear bolt and hex nut. Should a for- eign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug Place wire where it cannot come in contact with plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shoulder/shear bolt and spacer. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Connect spark plug wire to spark plug. Replace safety ignition key.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever is engaged, check to see if the capscrews have sheared. To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug Place wire where it cannot come in contact with plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

SPACER

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 19

TO REMOVE BELT COVER (See Fig. 20)

1.Remove the two screws securing belt cover to frame.

2.Remove belt cover.

•Replace belt cover by installing cover and screws and tighten securely.

FRAME

BELT COVER

SCREWS

FIG. 20

TO REPLACE BELTS (See Fig. 21)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a qualified service center.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to

15 the snow thrower.

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for startingDischarge chute control lever used to change the di Stopping HOW to USE Your Snow ThrowerUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig ADD Gasoline See Fig Before Starting the EngineScraper BAR Check Engine OIL Level See FigSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance Engine CleaningService and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Other StorageTroubleshooting Service Notes AIG plugr1 KEY Part Description 07Chute-knob2 414280 Knob, Lever Repair Parts Snow Thrower - Model NO. PR5524ES Handles Repair Parts Snow Thrower - Model NO. PR5524ES Handles Repair Parts Snow Thrower - Model NO. PR5524ES KEY Part Description   416717X004 17490508403096X004 402856X004Page 418962 418963 181037 Decal, DangerLimited Warranty

418962 specifications

The Poulan 418962 is a powerful and versatile chainsaw designed for both professional landscapers and homeowners looking to tackle a variety of cutting tasks. With its robust design and advanced features, this chainsaw has garnered attention for its reliability and performance.

One of the standout features of the Poulan 418962 is its efficient engine. Powered by a 40cc, 2-cycle engine, it delivers significant power for cutting through different types of wood, including hardwoods and softwoods. The engine is designed with an easy-start feature, which allows for quick and effortless starting, reducing frustration during operation. This is particularly beneficial for users who need to make quick cuts without the hassle of extensive warm-up sessions.

The chainsaw also comes equipped with a 16-inch bar and chain, offering excellent cutting capacity while maintaining a lightweight design. This balance allows users to maneuver the saw easily, making it ideal for pruning trees, cutting firewood, or clearing fallen debris. The low-kickback design of the chain enhances safety, reducing the risk of injury during operation.

In terms of technology, the Poulan 418962 features an automatic chain lubrication system. This system ensures that the chain remains sufficiently lubricated while in use, extending its lifespan and improving cutting efficiency. Users can easily monitor the oil level through a transparent oil tank, making maintenance straightforward.

Another critical characteristic of this chainsaw is its ergonomic design. The comfortable handle provides a secure grip, reducing fatigue during prolonged use. This is especially useful for those who may be working on extensive cutting projects. Additionally, the chainsaw is designed to absorb vibrations, further enhancing user comfort.

Safety features are also a focal point of the Poulan 418962. It includes a chain brake that can quickly stop the chain in case of kickback, ensuring user protection. Furthermore, the rear handle is equipped with a trigger lockout, preventing accidental starts.

Overall, the Poulan 418962 stands out as a reliable and efficient tool, marrying power with user-friendly features. Its combination of an efficient engine, automatic lubrication, safety precautions, and ergonomic design makes it an excellent choice for anyone looking to invest in a quality chainsaw. Whether for occasional use or frequent tasks, the Poulan 418962 delivers performance and durability that users can count on.
Top Page Image Contents