Poulan 418962 owner manual To Remove Wheels See Fig

Page 16

SERVICE AND ADJUSTMENTS

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler

arm bracket while bringing snow thrower together),

 

separate the snow thrower and repeat step 10. Belt

 

must be fully seated in pulley groove when bringing

16

the snow thrower together.

12.Install the two (2) hex boltsand tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lockwasher and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

 

AUGER

SQUARE

 

BELT

HOLE

 

 

CLUTCHING

 

IDLER ARM

 

BRACKET

 

 

AUGER PULLEY

 

 

 

BOLT

FRAME

AUGER

 

HOUSING

 

FIG. 21

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 22

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYRecoil auxiliary starter handle used for starting Meets A.N.S.I. Safety RequirementsDischarge chute control lever used to change the di HOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine Scraper BARCheck Engine OIL Level See Fig ADD Gasoline See FigBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Cleaning EngineTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector To Remove Wheels See Fig Storage OtherTroubleshooting Service Notes AIG plugr1 KEY Part Description 07Chute-knob2 414280 Knob, Lever Repair Parts Snow Thrower - Model NO. PR5524ES Handles Repair Parts Snow Thrower - Model NO. PR5524ES Handles Repair Parts Snow Thrower - Model NO. PR5524ES KEY Part Description   17490508 403096X004402856X004 416717X004Page 181037 Decal, Danger 418962 418963Limited Warranty

418962 specifications

The Poulan 418962 is a powerful and versatile chainsaw designed for both professional landscapers and homeowners looking to tackle a variety of cutting tasks. With its robust design and advanced features, this chainsaw has garnered attention for its reliability and performance.

One of the standout features of the Poulan 418962 is its efficient engine. Powered by a 40cc, 2-cycle engine, it delivers significant power for cutting through different types of wood, including hardwoods and softwoods. The engine is designed with an easy-start feature, which allows for quick and effortless starting, reducing frustration during operation. This is particularly beneficial for users who need to make quick cuts without the hassle of extensive warm-up sessions.

The chainsaw also comes equipped with a 16-inch bar and chain, offering excellent cutting capacity while maintaining a lightweight design. This balance allows users to maneuver the saw easily, making it ideal for pruning trees, cutting firewood, or clearing fallen debris. The low-kickback design of the chain enhances safety, reducing the risk of injury during operation.

In terms of technology, the Poulan 418962 features an automatic chain lubrication system. This system ensures that the chain remains sufficiently lubricated while in use, extending its lifespan and improving cutting efficiency. Users can easily monitor the oil level through a transparent oil tank, making maintenance straightforward.

Another critical characteristic of this chainsaw is its ergonomic design. The comfortable handle provides a secure grip, reducing fatigue during prolonged use. This is especially useful for those who may be working on extensive cutting projects. Additionally, the chainsaw is designed to absorb vibrations, further enhancing user comfort.

Safety features are also a focal point of the Poulan 418962. It includes a chain brake that can quickly stop the chain in case of kickback, ensuring user protection. Furthermore, the rear handle is equipped with a trigger lockout, preventing accidental starts.

Overall, the Poulan 418962 stands out as a reliable and efficient tool, marrying power with user-friendly features. Its combination of an efficient engine, automatic lubrication, safety precautions, and ergonomic design makes it an excellent choice for anyone looking to invest in a quality chainsaw. Whether for occasional use or frequent tasks, the Poulan 418962 delivers performance and durability that users can count on.
Top Page Image Contents