Poulan 418962 owner manual Before Starting the Engine, Scraper BAR, Check Engine OIL Level See Fig

Page 11

OPERATION

TON TE:ADJUSTThe wrenchSKID PLATESprovided(Seein yourFig.parts17) bag may be

usedNOTE:to Theadjustwrenchthe skidprovidedplates. in your parts bag may be usedSkid platesto adjustarethelocatedskid plateson each. side of the auger housing andSkidadjustplatestheareclearancelocated onbeachtweensidetheofscraperthe augerbarhousingand the groundand adjustsurfacethe clearance. Adjust skidbetweenplates theevenlyscraperto properbar andheightthe forgroundcurrentsurfacesurface. Adjustcondskitionsd plates. Forevenlyremovalto properf snowheightin normalfor currentcondisurfacetions, suchconditionsas a paved. Fordrivewayremoval orofsidesnowwalk,in placenormalskidcondiplatestions,insuchthe ashighesta pavedpositiondriveway(lowestor sidescraperwalk, clearplaceance)skid platesto giveina the1/8"highestclearancepositionbetween(lowestthe scraper barclearandance)thetogroundgive a. 1/8"Use clearancemiddle positionbetweenif the scraperurface tobarbeandclearedthe groundis uneven. Use. a middle position if the surface

toNOTE:be clearedIt is notisrecommendeduneven. to operate the snow thrower

overNOTE:gravelIt is ornotrockyrecommendedsurfaces. Objectsto operatesuchtheassnowgravel,throwerrocks overothergraveldebris,or rockyansurfaceseasily be. Objectspicked upsuchandasthrowngravel,byrocksthe impeller,or other debris,which cancauseeasilyseriousbe pickedpersonalup andinjury,thrownpropertyby the damimpeller,age whichor damagecan causeto theserioussnow throwerpersonal. injury, property

dam• Ifagesnowor damagethrower mustto thebesnowoperatedthrowerover. gravel surface, use extra caution and be sure skid platesgravelare adjusted

• If snow thrower must be operated over surface, to lowest (highest scraper clearance) position.

use extra caution and be sure skid plates are adjusted

1. toShutlowestoff engine(highestandscraperwait forclearall movingance) positionparts to. stop.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

12. ShutAdjustoffskidengineplatesandbywaitlooseningfor all movingthe rearparts1/2"tohexstopnut. only, then moving skid plate to desired position. Be sure

2. Adjust skid plates by loosening the hex nuts, then mov- both plates are adjusted evenly. Tighten securely. ing skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

SCRAPER BAR

HIGH POSITION

 

(LOW GROUND

 

CLEARANCE)

 

 

AUGER

 

HOUSING

 

SCRAPER BAR

HEX

SKID PLATE

NUTS

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 17

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed,

CHOKE CONTROL

SAFETY

IGNITION

KEY

RECOIL

STARTER

HANDLE

THROTTLE PRIMER ENGINE OIL FILL CAP / DIPSTICK

GASOLINE

FILLER CAP

FUEL SHUT-

OFF VALVE

STARTER BUTTON

POWER CORD PLUG

providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 18)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 18)

•Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 18

TO START ENGINE

•Be sure fuel shut-off valve is in the OPEN position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Se- rious personal injury or damage to your snow thrower could result.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Ignition KEY OperationKnow Your Snow Thrower PrimerDischarge chute control lever used to change the di Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig ADD Gasoline See Fig Before Starting the EngineScraper BAR Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Other StorageTroubleshooting Service Notes AIG plugr1 KEY Part Description 07Chute-knob2 414280 Knob, Lever Repair Parts Snow Thrower - Model NO. PR5524ES Handles Repair Parts Snow Thrower - Model NO. PR5524ES Handles Repair Parts Snow Thrower - Model NO. PR5524ES KEY Part Description   416717X004 17490508403096X004 402856X004Page 418962 418963 181037 Decal, DangerLimited Warranty

418962 specifications

The Poulan 418962 is a powerful and versatile chainsaw designed for both professional landscapers and homeowners looking to tackle a variety of cutting tasks. With its robust design and advanced features, this chainsaw has garnered attention for its reliability and performance.

One of the standout features of the Poulan 418962 is its efficient engine. Powered by a 40cc, 2-cycle engine, it delivers significant power for cutting through different types of wood, including hardwoods and softwoods. The engine is designed with an easy-start feature, which allows for quick and effortless starting, reducing frustration during operation. This is particularly beneficial for users who need to make quick cuts without the hassle of extensive warm-up sessions.

The chainsaw also comes equipped with a 16-inch bar and chain, offering excellent cutting capacity while maintaining a lightweight design. This balance allows users to maneuver the saw easily, making it ideal for pruning trees, cutting firewood, or clearing fallen debris. The low-kickback design of the chain enhances safety, reducing the risk of injury during operation.

In terms of technology, the Poulan 418962 features an automatic chain lubrication system. This system ensures that the chain remains sufficiently lubricated while in use, extending its lifespan and improving cutting efficiency. Users can easily monitor the oil level through a transparent oil tank, making maintenance straightforward.

Another critical characteristic of this chainsaw is its ergonomic design. The comfortable handle provides a secure grip, reducing fatigue during prolonged use. This is especially useful for those who may be working on extensive cutting projects. Additionally, the chainsaw is designed to absorb vibrations, further enhancing user comfort.

Safety features are also a focal point of the Poulan 418962. It includes a chain brake that can quickly stop the chain in case of kickback, ensuring user protection. Furthermore, the rear handle is equipped with a trigger lockout, preventing accidental starts.

Overall, the Poulan 418962 stands out as a reliable and efficient tool, marrying power with user-friendly features. Its combination of an efficient engine, automatic lubrication, safety precautions, and ergonomic design makes it an excellent choice for anyone looking to invest in a quality chainsaw. Whether for occasional use or frequent tasks, the Poulan 418962 delivers performance and durability that users can count on.
Top Page Image Contents