Poulan 421469 owner manual Before Starting the Engine, To Start Engine

Page 11

OPERATION

TO ADJUST SKID PLATES (See Fig. 17)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

• If snow thrower must be operated over gravel surface,

use extra caution and be sure skid plates are adjusted

to lowest (highest scraper clearance) position.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gaso- hol or using ethanol or methanol) can attract moisture which leads to separation and forma- tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the hex nuts, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION

 

(LOW GROUND

 

CLEARANCE)

 

 

AUGER

 

HOUSING

 

SCRAPER BAR

HEX

SKID PLATE

NUTS

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 17

SCRAPER BAR (See Fig. 17)

CHOKE CONTROL

SAFETY

IGNITION

KEY

RECOIL

STARTER

HANDLE

THROTTLE PRIMER ENGINE OIL FILL CAP / DIPSTICK

GASOLINE

FILLER CAP

FUEL SHUT-

OFF VALVE

STARTER BUTTON

POWER CORD PLUG

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 18)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 18)

•Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

11

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 22

TO START ENGINE

•Be sure fuel shut-off valve is in the “OPEN” position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Seri- ous personal injury or damage to your snow thrower could result.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Frame Auger Assembly Housing Handles Fuel System StorageCarburetor Engine SpeedCylinder OtherTroubleshooting Auger Bearing Auger HousingKEY Part Description Scraper BARSkid Plate RH Auger 27 LHAuger 27 RH Skid Plate LHExploded Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool BearingStrap Chute WeldmentDeflector Weldment Deflector SealRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Rotator HeadRepair Parts Snow Thrower - Model NO. PR8527ES Handles Loop Handle RH Loop Handle LHTraction ROD ARM Control PanelControl Lever LH Control Lever RHCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Repair Parts Snow Thrower - Model NO. PR8527ES Drive Control ARM 43 402689 Drive Plate AssemblySpeed Selector Assem BLY END PlateClik PIN Axle ShaftRoll PIN 3/16 SprocketEngine Mount Plate ENGINE, TECFrame Impeller Belt Belt CoverTraction Belt Wheel Assembly LH Repair Parts Snow Thrower - Model NO. PR8527ES Wheels35062 Repair Parts Snow Thrower - Model NO. PR8527ES BAG of PartsSafety Ignition KEY DECAL, DANGER, Deflector Repair Parts Snow Thrower - Model NO. PR8527ES Decals181037 DECAL, DangerService Notes Service Notes Limited Warranty

421469 specifications

The Poulan 421469 is a notable chainsaw model widely recognized for its robustness and efficiency, making it a preferred choice among both professional landscapers and casual users alike. This chainsaw is designed to handle a variety of cutting tasks, from felling small trees to pruning branches, thanks to its reliable performance and user-friendly features.

One of the main features of the Poulan 421469 is its powerful engine. The chainsaw is equipped with a 42cc two-stroke engine, providing ample power to tackle tough cutting jobs. This engine design ensures a balance between power and fuel efficiency, allowing users to extend their cutting time without frequent stops for refueling.

The chainsaw is also notable for its 18-inch bar and chain, which not only enhances its cutting capacity but also enables smooth and efficient cuts through various types of wood. The length of the bar allows for increased reach, making it easier to handle larger branches and logs. The high-quality chain ensures durability and sharpness, providing clean cuts without excessive effort.

In addition to its power, the Poulan 421469 incorporates several technologies aimed at improving the user experience. The chainsaw features an automatic oiling system, ensuring that the bar and chain are adequately lubricated during operation. This feature reduces maintenance time for users and enhances the lifespan of the components.

Furthermore, the chainsaw is designed with an ergonomic handle, which offers comfort and control during prolonged use. The lightweight construction of the unit reduces fatigue, enabling users to work for extended periods without discomfort. A safety switch and chain brake enhance user protection, making the chainsaw a safer choice for both beginners and experienced operators.

The Poulan 421469 also emphasizes ease of use, with a tool-free assembly system that simplifies the process of changing the chain or bar. This feature is particularly appealing to users who may not be familiar with more complex chainsaw mechanisms.

In summary, the Poulan 421469 embodies a perfect blend of power, efficiency, and user-friendly features. With its strong engine, robust cutting capability, and thoughtful design elements, it stands out as a reliable and versatile tool for anyone in need of a dependable chainsaw. Whether for professional use or occasional yard work, the Poulan 421469 is equipped to meet diverse cutting needs with confidence.
Top Page Image Contents