Poulan 421469 owner manual Safe Operation Practices for Walk-Behind Snow Throwers

Page 2

IMPORTANT

Safe Operation Practices for Walk-Behind Snow Throwers

This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury.

Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

WARNING: Always Remove safety igni- tion key and disconnect spark plug wire and place it where it cannot contact plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs.

WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping sur- faces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings.

Training

1.Read, understand and follow all instructions on the machine and in the manual(s) before operating this unit. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

2.Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction.

3.Keep the area of operation clear of all persons, par- ticularly small children.

4.Exercise caution to avoid slipping or falling, especially when operating the snow thrower in reverse.

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemi- cals known to the State of California to cause cancer and birth defects or other reproductive harm.

(f)Keep the nozzle in contact with the rim of the fuel tank or container opening at all times, until refuel- ing is complete. Do not use a nozzle lock-open device.

(g)Replace gasoline cap securely and wipe up spilled fuel.

(h)If fuel is spilled on clothing, change clothing im- mediately.

5.Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors or electric starting motors.

6.Adjust the collector housing height to clear gravel or crushed rock surface.

Preparation

1. Thoroughly inspect the area where the equipment is to be used and remove all doormats, sleds, boards, wires, and other foreign objects.

2. Disengage all clutches and shift into neutral before starting the engine (motor).

3. Do not operate the equipment without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear footwear that will improve footing on slippery surfaces.

4. Handle fuel with care; it is highly flammable

(a) Use an approved fuel container.

(b) Never add fuel to a running engine or hot en- gine.

(c) Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

(d) Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground, away from your vehicle, before filling.

(e) When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

2

7.Never attempt to make any adjustments while the engine (motor) is running (except when specifically recommended by manufacturer).

8.Always wear safety glasses or eye shields during op- eration or while performing an adjustment or repair to protect eyes from foreign objects that may be thrown from the machine.

Operation

1.Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

2.Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

3.After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, disconnect the cord on electric motors, thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

4.If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

5.Stop the engine (motor) whenever you leave the oper- ating position, before unclogging the collector/impeller housing or discharge chute, and when making any repairs, adjustments or inspections.

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine To Start EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Frame Auger Assembly Housing Handles Engine Speed StorageCarburetor Fuel SystemOther CylinderTroubleshooting Scraper BAR Auger HousingKEY Part Description Auger BearingSkid Plate LH Auger 27 LHAuger 27 RH Skid Plate RHExploded Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller PulleyDeflector Seal Chute WeldmentDeflector Weldment StrapRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Rotator Pivot BracketRepair Parts Snow Thrower - Model NO. PR8527ES Handles Loop Handle LH Loop Handle RHControl Lever RH Control PanelControl Lever LH Traction ROD ARMCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Repair Parts Snow Thrower - Model NO. PR8527ES Drive END Plate 43 402689 Drive Plate AssemblySpeed Selector Assem BLY Control ARMSprocket Axle ShaftRoll PIN 3/16 Clik PINEngine Mount Plate ENGINE, TECFrame Impeller Belt Belt CoverTraction Belt Repair Parts Snow Thrower - Model NO. PR8527ES Wheels Wheel Assembly LH35062 Repair Parts Snow Thrower - Model NO. PR8527ES BAG of PartsSafety Ignition KEY DECAL, Danger Repair Parts Snow Thrower - Model NO. PR8527ES Decals181037 DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

421469 specifications

The Poulan 421469 is a notable chainsaw model widely recognized for its robustness and efficiency, making it a preferred choice among both professional landscapers and casual users alike. This chainsaw is designed to handle a variety of cutting tasks, from felling small trees to pruning branches, thanks to its reliable performance and user-friendly features.

One of the main features of the Poulan 421469 is its powerful engine. The chainsaw is equipped with a 42cc two-stroke engine, providing ample power to tackle tough cutting jobs. This engine design ensures a balance between power and fuel efficiency, allowing users to extend their cutting time without frequent stops for refueling.

The chainsaw is also notable for its 18-inch bar and chain, which not only enhances its cutting capacity but also enables smooth and efficient cuts through various types of wood. The length of the bar allows for increased reach, making it easier to handle larger branches and logs. The high-quality chain ensures durability and sharpness, providing clean cuts without excessive effort.

In addition to its power, the Poulan 421469 incorporates several technologies aimed at improving the user experience. The chainsaw features an automatic oiling system, ensuring that the bar and chain are adequately lubricated during operation. This feature reduces maintenance time for users and enhances the lifespan of the components.

Furthermore, the chainsaw is designed with an ergonomic handle, which offers comfort and control during prolonged use. The lightweight construction of the unit reduces fatigue, enabling users to work for extended periods without discomfort. A safety switch and chain brake enhance user protection, making the chainsaw a safer choice for both beginners and experienced operators.

The Poulan 421469 also emphasizes ease of use, with a tool-free assembly system that simplifies the process of changing the chain or bar. This feature is particularly appealing to users who may not be familiar with more complex chainsaw mechanisms.

In summary, the Poulan 421469 embodies a perfect blend of power, efficiency, and user-friendly features. With its strong engine, robust cutting capability, and thoughtful design elements, it stands out as a reliable and versatile tool for anyone in need of a dependable chainsaw. Whether for professional use or occasional yard work, the Poulan 421469 is equipped to meet diverse cutting needs with confidence.
Top Page Image Contents