Poulan 421469 owner manual Storage, Carburetor, Engine Speed, Fuel System, Engine OIL

Page 17

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 22

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Frame Auger Assembly Housing Handles Carburetor StorageEngine Speed Fuel SystemCylinder OtherTroubleshooting KEY Part Description Auger HousingScraper BAR Auger BearingAuger 27 RH Auger 27 LHSkid Plate LH Skid Plate RHExploded 178675X008 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller PulleyDeflector Weldment Chute WeldmentDeflector Seal StrapCable Assembly LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketRepair Parts Snow Thrower - Model NO. PR8527ES Handles Loop Handle RH Loop Handle LHControl Lever LH Control PanelControl Lever RH Traction ROD ARMCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Repair Parts Snow Thrower - Model NO. PR8527ES Drive Speed Selector Assem BLY 43 402689 Drive Plate AssemblyEND Plate Control ARMRoll PIN 3/16 Axle ShaftSprocket Clik PINEngine Mount Plate ENGINE, TECFrame Impeller Belt Belt CoverTraction Belt Wheel Assembly LH Repair Parts Snow Thrower - Model NO. PR8527ES Wheels35062 Repair Parts Snow Thrower - Model NO. PR8527ES BAG of PartsSafety Ignition KEY 181037 Repair Parts Snow Thrower - Model NO. PR8527ES DecalsDECAL, Danger DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

421469 specifications

The Poulan 421469 is a notable chainsaw model widely recognized for its robustness and efficiency, making it a preferred choice among both professional landscapers and casual users alike. This chainsaw is designed to handle a variety of cutting tasks, from felling small trees to pruning branches, thanks to its reliable performance and user-friendly features.

One of the main features of the Poulan 421469 is its powerful engine. The chainsaw is equipped with a 42cc two-stroke engine, providing ample power to tackle tough cutting jobs. This engine design ensures a balance between power and fuel efficiency, allowing users to extend their cutting time without frequent stops for refueling.

The chainsaw is also notable for its 18-inch bar and chain, which not only enhances its cutting capacity but also enables smooth and efficient cuts through various types of wood. The length of the bar allows for increased reach, making it easier to handle larger branches and logs. The high-quality chain ensures durability and sharpness, providing clean cuts without excessive effort.

In addition to its power, the Poulan 421469 incorporates several technologies aimed at improving the user experience. The chainsaw features an automatic oiling system, ensuring that the bar and chain are adequately lubricated during operation. This feature reduces maintenance time for users and enhances the lifespan of the components.

Furthermore, the chainsaw is designed with an ergonomic handle, which offers comfort and control during prolonged use. The lightweight construction of the unit reduces fatigue, enabling users to work for extended periods without discomfort. A safety switch and chain brake enhance user protection, making the chainsaw a safer choice for both beginners and experienced operators.

The Poulan 421469 also emphasizes ease of use, with a tool-free assembly system that simplifies the process of changing the chain or bar. This feature is particularly appealing to users who may not be familiar with more complex chainsaw mechanisms.

In summary, the Poulan 421469 embodies a perfect blend of power, efficiency, and user-friendly features. With its strong engine, robust cutting capability, and thoughtful design elements, it stands out as a reliable and versatile tool for anyone in need of a dependable chainsaw. Whether for professional use or occasional yard work, the Poulan 421469 is equipped to meet diverse cutting needs with confidence.
Top Page Image Contents