Poulan 421028 owner manual Storage, Carburetor, Engine Speed, Fuel System, Engine OIL

Page 17

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 22

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Frame Auger Assembly Housing Handles Carburetor StorageEngine Speed Fuel SystemCylinder OtherTroubleshooting KEY Part Description Auger HousingScraper BAR Auger BearingAuger 27 RH Auger 27 LHSkid Plate LH Skid Plate RHExploded 178675X008 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller PulleyDeflector Weldment Chute WeldmentDeflector Seal StrapCable Assembly LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketRepair Parts Snow Thrower - Model NO. PR8527ES Handles Loop Handle RH Loop Handle LHControl Lever LH Control PanelControl Lever RH Traction ROD ARMCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Repair Parts Snow Thrower - Model NO. PR8527ES Drive END Plate 43 420900 Drive Plate AssemblyControl ARM Clevis PINRoll PIN 3/16 Axle ShaftSprocket Clik PINEngine Mount Plate ENGINE, TECFrame Impeller Belt Belt CoverTraction Belt Wheel Assembly LH Repair Parts Snow Thrower - Model NO. PR8527ES Wheels35062 Repair Parts Snow Thrower - Model NO. PR8527ES BAG of PartsSafety Ignition KEY 181037 Repair Parts Snow Thrower - Model NO. PR8527ES DecalsDECAL, Danger DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

421028 specifications

The Poulan 421028 is a notable chainsaw that has gained attention among both casual users and professionals due to its blend of power, efficiency, and user-friendly design. This model is especially suited for light to medium-duty tasks, making it an ideal choice for homeowners and those looking to tackle yard work or firewood preparation.

One of the standout features of the Poulan 421028 is its powerful engine. It typically comes with a 42cc two-stroke engine that delivers a robust performance, allowing users to cut through various types of wood with ease. The power output ensures that even demanding tasks can be completed efficiently, making it suitable for felling small trees, trimming branches, and cutting logs.

In addition to power, the Poulan 421028 is designed with user comfort in mind. It features an ergonomic design that reduces operator fatigue, allowing for extended use without discomfort. The lightweight construction of the chainsaw contributes to its ease of maneuverability, making it accessible for users of different skill levels.

The chainsaw is equipped with an adjustable automatic oiling system that ensures optimal lubrication of the bar and chain during operation. This technology not only enhances the lifespan of the components but also ensures that the chainsaw runs smoothly, reducing the risk of overheating and wear.

Safety is another critical aspect of the Poulan 421028. It includes reliable safety features such as a chain brake, which immediately stops the chain's rotation in the event of kickback, protecting the user from potential injuries. Additionally, the front guard serves to shield hands from debris and other hazards, ensuring a safer cutting environment.

Ease of maintenance is a key consideration for any user, and the Poulan 421028 shines in this aspect as well. It comes with a tool-less access feature for the air filter and spark plug, simplifying routine maintenance tasks. This convenience helps users keep the chainsaw in peak operating condition with minimal effort.

In conclusion, the Poulan 421028 is a versatile and reliable chainsaw that combines power, comfort, and safety features, making it an excellent choice for various cutting tasks. Its user-friendly design, impressive engine performance, and ease of maintenance make it a valuable tool for both novice and experienced users alike. Whether you're tackling yard work or preparing firewood, the Poulan 421028 provides the efficiency and reliability needed to get the job done effectively.
Top Page Image Contents