Poulan 421028 owner manual Before Starting the Engine, To Start Engine

Page 11

OPERATION

TO ADJUST SKID PLATES (See Fig. 17)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

• If snow thrower must be operated over gravel surface,

use extra caution and be sure skid plates are adjusted

to lowest (highest scraper clearance) position.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gaso- hol or using ethanol or methanol) can attract moisture which leads to separation and forma- tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the hex nuts, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION

 

(LOW GROUND

 

CLEARANCE)

 

 

AUGER

 

HOUSING

 

SCRAPER BAR

HEX

SKID PLATE

NUTS

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 17

SCRAPER BAR (See Fig. 17)

CHOKE CONTROL

SAFETY

IGNITION

KEY

RECOIL

STARTER

HANDLE

THROTTLE PRIMER ENGINE OIL FILL CAP / DIPSTICK

GASOLINE

FILLER CAP

FUEL SHUT-

OFF VALVE

STARTER BUTTON

POWER CORD PLUG

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 18)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 18)

•Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

11

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 22

TO START ENGINE

•Be sure fuel shut-off valve is in the “OPEN” position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Seri- ous personal injury or damage to your snow thrower could result.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Frame Auger Assembly Housing Handles Fuel System StorageCarburetor Engine SpeedCylinder OtherTroubleshooting Auger Bearing Auger HousingKEY Part Description Scraper BARSkid Plate RH Auger 27 LHAuger 27 RH Skid Plate LHExploded Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool BearingStrap Chute WeldmentDeflector Weldment Deflector SealRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Rotator HeadRepair Parts Snow Thrower - Model NO. PR8527ES Handles Loop Handle RH Loop Handle LHTraction ROD ARM Control PanelControl Lever LH Control Lever RHCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Repair Parts Snow Thrower - Model NO. PR8527ES Drive Clevis PIN 43 420900 Drive Plate AssemblyEND Plate Control ARMClik PIN Axle ShaftRoll PIN 3/16 SprocketEngine Mount Plate ENGINE, TECFrame Impeller Belt Belt CoverTraction Belt Wheel Assembly LH Repair Parts Snow Thrower - Model NO. PR8527ES Wheels35062 Repair Parts Snow Thrower - Model NO. PR8527ES BAG of PartsSafety Ignition KEY DECAL, DANGER, Deflector Repair Parts Snow Thrower - Model NO. PR8527ES Decals181037 DECAL, DangerService Notes Service Notes Limited Warranty

421028 specifications

The Poulan 421028 is a notable chainsaw that has gained attention among both casual users and professionals due to its blend of power, efficiency, and user-friendly design. This model is especially suited for light to medium-duty tasks, making it an ideal choice for homeowners and those looking to tackle yard work or firewood preparation.

One of the standout features of the Poulan 421028 is its powerful engine. It typically comes with a 42cc two-stroke engine that delivers a robust performance, allowing users to cut through various types of wood with ease. The power output ensures that even demanding tasks can be completed efficiently, making it suitable for felling small trees, trimming branches, and cutting logs.

In addition to power, the Poulan 421028 is designed with user comfort in mind. It features an ergonomic design that reduces operator fatigue, allowing for extended use without discomfort. The lightweight construction of the chainsaw contributes to its ease of maneuverability, making it accessible for users of different skill levels.

The chainsaw is equipped with an adjustable automatic oiling system that ensures optimal lubrication of the bar and chain during operation. This technology not only enhances the lifespan of the components but also ensures that the chainsaw runs smoothly, reducing the risk of overheating and wear.

Safety is another critical aspect of the Poulan 421028. It includes reliable safety features such as a chain brake, which immediately stops the chain's rotation in the event of kickback, protecting the user from potential injuries. Additionally, the front guard serves to shield hands from debris and other hazards, ensuring a safer cutting environment.

Ease of maintenance is a key consideration for any user, and the Poulan 421028 shines in this aspect as well. It comes with a tool-less access feature for the air filter and spark plug, simplifying routine maintenance tasks. This convenience helps users keep the chainsaw in peak operating condition with minimal effort.

In conclusion, the Poulan 421028 is a versatile and reliable chainsaw that combines power, comfort, and safety features, making it an excellent choice for various cutting tasks. Its user-friendly design, impressive engine performance, and ease of maintenance make it a valuable tool for both novice and experienced users alike. Whether you're tackling yard work or preparing firewood, the Poulan 421028 provides the efficiency and reliability needed to get the job done effectively.
Top Page Image Contents