Poulan 96194000602, 418984 owner manual Snow Throwing Tips, To Start Engine, Before Stopping

Page 13

OPERATION

TO START ENGINE

•Be sure fuel shut-off valve is in the “OPEN” position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Se- rious personal injury or damage to your snow thrower could result.

COLD START - ELECTRIC STARTER

1.Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place throttle control in “FAST” position.

3.Rotate choke control to “FULL” position.

4.Connect the power cord to the engine.

5.Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle.

6.Push the primer three (3) times.

7.Push starter button until engine starts.

IMPORTANT: Do not crank engine more than five con- tinuous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt.

8.When the engine starts, release the starter button and slowly move the choke control to the “OFF” position.

9.Disconnect the power cord from the receptacle first, then from the engine.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the “OFF” position.

COLD START - RECOIL STARTER

1.Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place throttle control in “FAST” position.

3.Rotate choke control to “FULL” position.

4.Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the “OFF” posi- tion.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the “OFF” position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps or use the electric starter.

SNOW THROWING TIPS

•Always operate the snow thrower with the engine at full throttle. Full throttle offers the best performance.

•Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the throttle, to adjust speed.

•It is easier and more efficient to remove snow imme- diately after it falls.

•The best time to remove snow is the early morning. At this time the snow is usually dry and has not been ex- posed to the direct sun and warming temperatures.

•Slightly overlap each successive path to ensure all snow will be removed.

•Throw snow downwind whenever possible.

•Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

•For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

•Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

•After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

•Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditionsimpair vis- ibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage Other TroubleshootingPreparación ¡ATENCIÓN! ¡ESTE ALERTO! SU Seguridad Esta ComprometidaFuncionamiento Montaje / PRE-OPERACIÓN Tabla DE MateriasPartes Empacadas POR Separado EL LA Caja DE Cartón Sacar LA Máquina Quitanieves DEL Cartón Montaje / PRE-OPERACIÓNComo Preparar SU Máquina Quitanieves Desplegar LA Empuñadura SuperiorDE Mando DE LA Tracción Ver Figs y Montaje DE LA BielaDE Mando DE LA Barrena Ver Figs y Controlar LA Presión DE LOS Neumáticos Familiarícese CON SU Máquina Quitanieves OperaciónCumple CON LOS Requisitos DE Seguridad DE LA A.N.S.I Como Utilizar SU Máquina Quitanieves Controlar LA Eyección DE LA NievePararse Usar LA Herramienta Para Limpiar Ver Fig Lanzar LA Nieve Ver FigMoverse Adelante Y Atrás Ver Fig Funcionamiento DE LA Dirección Ver FigRegular LAS Placas DE Deslizamiento Ver Fig Antes DE Poner EN Marcha EL MotorBarra DE Arrastre Ver Fig Controlar EL Nivel DE Aceite DEL Motor Ver FigPuesta EN Marcha DEL Motor Consejos Para Lanzar LA NieveAntes DE Parar SI EL Arrancador DE Retroceso SE HA CongeladoRecomendaciones Generales MantenamientoLubricación Maquina QuitanievesLimpieza MotorPara Ajustar LA Altura DE Máquina Quitanieves Servicio Y AdjustesConducto Deflector Pernos DE Seguridad Ver FigVaciar LA Gasolina DEL Depósito DE Carburante Sustituir LAS Correas Vea FigOtros AlmacenimientoIdentificacion DE Problemas Page KEY Part Description Page 414280 Knob, Lever Repair Parts Snow Thrower Model Number Handles Repair Parts Snow Thrower Model Number 96194000602 Handles Repair Parts Snow Thrower Model Number 96194000602 Drive Repair Parts Snow Thrower Model Number 96194000602 Drive Page 416954 KEY Part Description416717X004 413429X479Repair Parts Snow Thrower Model Number 96194000602 Wheels KEY Part Description Repair Parts Snow Thrower Model Number 96194000602 Decals 406045 181038 Decal, DangerLimited Warranty

96194000602, 418984 specifications

The Poulan 96194000602,418984 is a powerful and versatile chainsaw designed to meet the demands of both professional landscapers and homeowners who require a reliable tool for their cutting needs. This chainsaw is equipped with several innovative features and technologies that set it apart from other models in the market.

At its core, the Poulan 96194000602 is powered by a robust 42cc, 2-cycle engine, which provides ample power for various tasks, from trimming branches to cutting down small trees. The engine is designed to deliver a strong performance while maintaining fuel efficiency, allowing users to work longer without frequent refueling. The incorporation of a gas-powered engine means that this chainsaw can deliver consistent power without the limitations of a battery-operated model.

One of the standout characteristics of this chainsaw is its ergonomic design. The lightweight construction and well-balanced design ensure user comfort, even during extended use. The chainsaw features an easy-to-grip handle, reducing fatigue and allowing for a more controlled cutting experience. Additionally, its anti-vibration technology helps minimize vibrations felt by the user, enhancing comfort and safety.

The Poulan 96194000602 is equipped with a 16-inch bar and chain, making it suitable for a variety of cutting tasks. The chainsaw's chain tensioning system allows for quick and convenient adjustments, ensuring optimal performance and longevity of the chain. The tool-less chain adjustment feature is especially beneficial for users who need to make adjustments quickly in the field.

Safety is also a priority in the design of the Poulan 96194000602. It comes with a built-in chain brake that instantly stops the chain's motion in the event of kickback, providing an added layer of safety to the user. Furthermore, the chainsaw features an automatic oiling system that ensures the chain is adequately lubricated during operation, reducing wear and tear.

In summary, the Poulan 96194000602,418984 chainsaw combines power, comfort, and safety features that make it an excellent choice for both homeowners and professionals alike. Whether you need to tackle yard work or outdoor projects, this chainsaw delivers reliability and performance, ensuring you can get the job done efficiently. With its user-friendly design and advanced technologies, the Poulan chainsaw is a smart investment for anyone in need of a high-quality cutting tool.
Top Page Image Contents