Poulan 418984, 96194000602 owner manual Safe Operation Practices for Walk-Behind Snow Throwers

Page 2

IMPORTANT

Safe Operation Practices for Walk-Behind Snow Throwers

This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury.

Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in order to prevent acci- dental starting when setting up, trans- porting, adjusting or making repairs.

WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping sur- faces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings.

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemi- cals known to the State of California to cause cancer and birth defects or other reproductive harm.

Training

1.Read, understand and follow all instructions on the machine and in the manual(s) before operating this unit. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

2.Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction.

3.Keep the area of operation clear of all persons, par- ticularly small children.

4.Exercise caution to avoid slipping or falling, especially when operating the snow thrower in reverse.

Preparation

1.Thoroughly inspect the area where the equipment is to be used and remove all doormats, sleds, boards, wires, and other foreign objects.

2.Disengage all clutches and shift into neutral before starting the engine (motor).

3.Do not operate the equipment without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear footwear that will improve footing on slippery surfaces.

4.Handle fuel with care; it is highly flammable

(a)Use an approved fuel container.

(b)Never add fuel to a running engine or hot en- gine.

(c)Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

(d)Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place contain- ers on the ground, away from your vehicle, before filling.

(e)When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

(f)Keep the nozzle in contact with the rim of the fuel tank or container opening at all times, until refuel- ing is complete. Do not use a nozzle lock-open device.

(g)Replace gasoline cap securely and wipe up spilled fuel.

(h)If fuel is spilled on clothing, change clothing im- mediately.

5.Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors or electric starting motors.

6.Adjust the collector housing height to clear gravel or crushed rock surface.

7.Never attempt to make any adjustments while the engine (motor) is running (except when specifically recommended by manufacturer).

8.Always wear safety glasses or eye shields during op- eration or while performing an adjustment or repair to protect eyes from foreign objects that may be thrown from the machine.

Operation

1.Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

2.Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

3.After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, disconnect the cord on electric motors, thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

4.If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

5.Stop the engine (motor) whenever you leave the oper- ating position, before unclogging the collector/impeller

 

housing or discharge chute, and when making any

2

repairs, adjustments or inspections.

 

Image 2
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage Troubleshooting OtherFuncionamiento ¡ATENCIÓN! ¡ESTE ALERTO! SU Seguridad Esta ComprometidaPreparación Tabla DE Materias Montaje / PRE-OPERACIÓNPartes Empacadas POR Separado EL LA Caja DE Cartón Como Preparar SU Máquina Quitanieves Montaje / PRE-OPERACIÓNSacar LA Máquina Quitanieves DEL Cartón Desplegar LA Empuñadura SuperiorDE Mando DE LA Barrena Ver Figs y Montaje DE LA BielaDE Mando DE LA Tracción Ver Figs y Controlar LA Presión DE LOS Neumáticos Operación Familiarícese CON SU Máquina QuitanievesCumple CON LOS Requisitos DE Seguridad DE LA A.N.S.I Pararse Controlar LA Eyección DE LA NieveComo Utilizar SU Máquina Quitanieves Moverse Adelante Y Atrás Ver Fig Lanzar LA Nieve Ver FigUsar LA Herramienta Para Limpiar Ver Fig Funcionamiento DE LA Dirección Ver FigBarra DE Arrastre Ver Fig Antes DE Poner EN Marcha EL MotorRegular LAS Placas DE Deslizamiento Ver Fig Controlar EL Nivel DE Aceite DEL Motor Ver FigAntes DE Parar Consejos Para Lanzar LA NievePuesta EN Marcha DEL Motor SI EL Arrancador DE Retroceso SE HA CongeladoLubricación MantenamientoRecomendaciones Generales Maquina QuitanievesMotor LimpiezaConducto Deflector Servicio Y AdjustesPara Ajustar LA Altura DE Máquina Quitanieves Pernos DE Seguridad Ver FigSustituir LAS Correas Vea Fig Vaciar LA Gasolina DEL Depósito DE CarburanteAlmacenimiento OtrosIdentificacion DE Problemas Page KEY Part Description Page 414280 Knob, Lever Repair Parts Snow Thrower Model Number Handles Repair Parts Snow Thrower Model Number 96194000602 Handles Repair Parts Snow Thrower Model Number 96194000602 Drive Repair Parts Snow Thrower Model Number 96194000602 Drive Page 416717X004 KEY Part Description416954 413429X479Repair Parts Snow Thrower Model Number 96194000602 Wheels KEY Part Description Repair Parts Snow Thrower Model Number 96194000602 Decals 181038 Decal, Danger 406045Limited Warranty

96194000602, 418984 specifications

The Poulan 96194000602,418984 is a powerful and versatile chainsaw designed to meet the demands of both professional landscapers and homeowners who require a reliable tool for their cutting needs. This chainsaw is equipped with several innovative features and technologies that set it apart from other models in the market.

At its core, the Poulan 96194000602 is powered by a robust 42cc, 2-cycle engine, which provides ample power for various tasks, from trimming branches to cutting down small trees. The engine is designed to deliver a strong performance while maintaining fuel efficiency, allowing users to work longer without frequent refueling. The incorporation of a gas-powered engine means that this chainsaw can deliver consistent power without the limitations of a battery-operated model.

One of the standout characteristics of this chainsaw is its ergonomic design. The lightweight construction and well-balanced design ensure user comfort, even during extended use. The chainsaw features an easy-to-grip handle, reducing fatigue and allowing for a more controlled cutting experience. Additionally, its anti-vibration technology helps minimize vibrations felt by the user, enhancing comfort and safety.

The Poulan 96194000602 is equipped with a 16-inch bar and chain, making it suitable for a variety of cutting tasks. The chainsaw's chain tensioning system allows for quick and convenient adjustments, ensuring optimal performance and longevity of the chain. The tool-less chain adjustment feature is especially beneficial for users who need to make adjustments quickly in the field.

Safety is also a priority in the design of the Poulan 96194000602. It comes with a built-in chain brake that instantly stops the chain's motion in the event of kickback, providing an added layer of safety to the user. Furthermore, the chainsaw features an automatic oiling system that ensures the chain is adequately lubricated during operation, reducing wear and tear.

In summary, the Poulan 96194000602,418984 chainsaw combines power, comfort, and safety features that make it an excellent choice for both homeowners and professionals alike. Whether you need to tackle yard work or outdoor projects, this chainsaw delivers reliability and performance, ensuring you can get the job done efficiently. With its user-friendly design and advanced technologies, the Poulan chainsaw is a smart investment for anyone in need of a high-quality cutting tool.