Poulan 418984, 96194000602 owner manual Storage

Page 18

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 24)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 24

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service centre.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service centre, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage Troubleshooting Other¡ATENCIÓN! ¡ESTE ALERTO! SU Seguridad Esta Comprometida PreparaciónFuncionamiento Tabla DE Materias Montaje / PRE-OPERACIÓNPartes Empacadas POR Separado EL LA Caja DE Cartón Como Preparar SU Máquina Quitanieves Montaje / PRE-OPERACIÓNSacar LA Máquina Quitanieves DEL Cartón Desplegar LA Empuñadura SuperiorMontaje DE LA Biela DE Mando DE LA Tracción Ver Figs yDE Mando DE LA Barrena Ver Figs y Controlar LA Presión DE LOS Neumáticos Operación Familiarícese CON SU Máquina QuitanievesCumple CON LOS Requisitos DE Seguridad DE LA A.N.S.I Controlar LA Eyección DE LA Nieve Como Utilizar SU Máquina QuitanievesPararse Moverse Adelante Y Atrás Ver Fig Lanzar LA Nieve Ver FigUsar LA Herramienta Para Limpiar Ver Fig Funcionamiento DE LA Dirección Ver FigBarra DE Arrastre Ver Fig Antes DE Poner EN Marcha EL MotorRegular LAS Placas DE Deslizamiento Ver Fig Controlar EL Nivel DE Aceite DEL Motor Ver FigAntes DE Parar Consejos Para Lanzar LA NievePuesta EN Marcha DEL Motor SI EL Arrancador DE Retroceso SE HA CongeladoLubricación MantenamientoRecomendaciones Generales Maquina QuitanievesMotor LimpiezaConducto Deflector Servicio Y AdjustesPara Ajustar LA Altura DE Máquina Quitanieves Pernos DE Seguridad Ver FigSustituir LAS Correas Vea Fig Vaciar LA Gasolina DEL Depósito DE CarburanteAlmacenimiento OtrosIdentificacion DE Problemas Page KEY Part Description Page 414280 Knob, Lever Repair Parts Snow Thrower Model Number Handles Repair Parts Snow Thrower Model Number 96194000602 Handles Repair Parts Snow Thrower Model Number 96194000602 Drive Repair Parts Snow Thrower Model Number 96194000602 Drive Page 416717X004 KEY Part Description416954 413429X479Repair Parts Snow Thrower Model Number 96194000602 Wheels KEY Part Description Repair Parts Snow Thrower Model Number 96194000602 Decals 181038 Decal, Danger 406045Limited Warranty

96194000602, 418984 specifications

The Poulan 96194000602,418984 is a powerful and versatile chainsaw designed to meet the demands of both professional landscapers and homeowners who require a reliable tool for their cutting needs. This chainsaw is equipped with several innovative features and technologies that set it apart from other models in the market.

At its core, the Poulan 96194000602 is powered by a robust 42cc, 2-cycle engine, which provides ample power for various tasks, from trimming branches to cutting down small trees. The engine is designed to deliver a strong performance while maintaining fuel efficiency, allowing users to work longer without frequent refueling. The incorporation of a gas-powered engine means that this chainsaw can deliver consistent power without the limitations of a battery-operated model.

One of the standout characteristics of this chainsaw is its ergonomic design. The lightweight construction and well-balanced design ensure user comfort, even during extended use. The chainsaw features an easy-to-grip handle, reducing fatigue and allowing for a more controlled cutting experience. Additionally, its anti-vibration technology helps minimize vibrations felt by the user, enhancing comfort and safety.

The Poulan 96194000602 is equipped with a 16-inch bar and chain, making it suitable for a variety of cutting tasks. The chainsaw's chain tensioning system allows for quick and convenient adjustments, ensuring optimal performance and longevity of the chain. The tool-less chain adjustment feature is especially beneficial for users who need to make adjustments quickly in the field.

Safety is also a priority in the design of the Poulan 96194000602. It comes with a built-in chain brake that instantly stops the chain's motion in the event of kickback, providing an added layer of safety to the user. Furthermore, the chainsaw features an automatic oiling system that ensures the chain is adequately lubricated during operation, reducing wear and tear.

In summary, the Poulan 96194000602,418984 chainsaw combines power, comfort, and safety features that make it an excellent choice for both homeowners and professionals alike. Whether you need to tackle yard work or outdoor projects, this chainsaw delivers reliability and performance, ensuring you can get the job done efficiently. With its user-friendly design and advanced technologies, the Poulan chainsaw is a smart investment for anyone in need of a high-quality cutting tool.
Top Page Image Contents