To Remove Wheels See Fig | Poulan 416810 instruction

SERVICE AND ADJUSTMENTS

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME	AUGER
ASSEMBLY	HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt

must be fully seated in pulley groove when bringing
the snow thrower together.	16

12.Install the two (2) hex bolts and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lockwasher and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

	BELT KEEPER
	TRACTION DRIVE BELT
	ENGINE	FLAT WASHER
	PULLEY	FLAT WASHER
	PULLEY
		LOCKWASHER
		BOLT
IDLER ARM		AUGER
SQUARE		BELT
HOLE
CLUTCHING
IDLER ARM
BRACKET
	AUGER PULLEY
		BOLT
FRAME	AUGER
FRAME	HOUSING

FIG. 21

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN	OUTER HOLE
	INNER
	HOLE
WHEEL	WHEEL HUB

FIG. 22

416810 specifications

The Poulan 416810 is a robust chainsaw designed for both professional and leisure use, making it a versatile tool for a range of applications. Known for its reliability and performance, this model is particularly favored among homeowners and landscapers for its power and ease of use.

One of the standout features of the Poulan 416810 is its powerful engine. The chainsaw is equipped with a 40cc two-stroke engine that delivers impressive cutting power while remaining relatively lightweight. This engine is designed not only to provide adequate horsepower but also to reduce fuel consumption, making it an economical choice. The advanced combustion system promotes cleaner burning, hence reducing emissions and making it more environmentally friendly.

The chainsaw boasts an innovative Easy Start Technology, which allows for effortless starting. This feature minimizes the wear and strain on the starter cord, making it particularly user-friendly for those who may not be experienced in handling chainsaws. Additionally, the automatic oiler ensures that the chain and bar receive the proper lubrication during use, enhancing performance and prolonging the lifespan of the tool.

Safety is also a critical aspect of the Poulan 416810. The tool is equipped with a chain brake that provides an added layer of protection by stopping the chain motion in the event of kickback. The anti-vibration feature helps reduce user fatigue during extended use, ensuring a comfortable grip and greater control.

The Poulan 416810 features an adjustable chain tensioning system, which allows users to adjust the chain quickly and easily without the need for any additional tools. This feature is essential for maintaining optimal performance and ensuring the safety of the operation.

In terms of design, the Poulan 416810 is built with ergonomics in mind. The lightweight design, combined with a well-balanced frame, makes it easy to maneuver, allowing users to work for extended periods without excessive strain. The comfortable handles offer a secure grip, improving handling during operation.

Overall, the Poulan 416810 is an efficient and reliable chainsaw that combines power, safety, and ease of use, making it an ideal choice for a variety of cutting tasks, whether it be trimming branches, felling trees, or performing general landscaping. Its combination of advanced technology and thoughtful design ensures that both novice and experienced users can handle a range of tasks effectively.