Poulan 416810 owner manual Storage, Other

Page 17

SERVICE AND ADJUSTMENTS

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYDischarge chute control lever used to change the di Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Other StorageTroubleshooting Service Notes AIG plugr1 KEY Part Description 07Chute-knob2 414280 Knob, Lever Repair Parts Snow Thrower - Model NO. PR8527ES Handles Repair Parts Snow Thrower - Model NO. PR8527ES Handles Repair Parts Snow Thrower - Model NO. PR8527ES Drive Repair Parts Snow Thrower - Model NO. PR8527ES Drive Page 413429X479 KEY Part Description416717X004 Page 416810 416811 Limited Warranty

416810 specifications

The Poulan 416810 is a robust chainsaw designed for both professional and leisure use, making it a versatile tool for a range of applications. Known for its reliability and performance, this model is particularly favored among homeowners and landscapers for its power and ease of use.

One of the standout features of the Poulan 416810 is its powerful engine. The chainsaw is equipped with a 40cc two-stroke engine that delivers impressive cutting power while remaining relatively lightweight. This engine is designed not only to provide adequate horsepower but also to reduce fuel consumption, making it an economical choice. The advanced combustion system promotes cleaner burning, hence reducing emissions and making it more environmentally friendly.

The chainsaw boasts an innovative Easy Start Technology, which allows for effortless starting. This feature minimizes the wear and strain on the starter cord, making it particularly user-friendly for those who may not be experienced in handling chainsaws. Additionally, the automatic oiler ensures that the chain and bar receive the proper lubrication during use, enhancing performance and prolonging the lifespan of the tool.

Safety is also a critical aspect of the Poulan 416810. The tool is equipped with a chain brake that provides an added layer of protection by stopping the chain motion in the event of kickback. The anti-vibration feature helps reduce user fatigue during extended use, ensuring a comfortable grip and greater control.

The Poulan 416810 features an adjustable chain tensioning system, which allows users to adjust the chain quickly and easily without the need for any additional tools. This feature is essential for maintaining optimal performance and ensuring the safety of the operation.

In terms of design, the Poulan 416810 is built with ergonomics in mind. The lightweight design, combined with a well-balanced frame, makes it easy to maneuver, allowing users to work for extended periods without excessive strain. The comfortable handles offer a secure grip, improving handling during operation.

Overall, the Poulan 416810 is an efficient and reliable chainsaw that combines power, safety, and ease of use, making it an ideal choice for a variety of cutting tasks, whether it be trimming branches, felling trees, or performing general landscaping. Its combination of advanced technology and thoughtful design ensures that both novice and experienced users can handle a range of tasks effectively.
Top Page Image Contents