Poulan P14530ES owner manual Engine, Cleaning

Page 14

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install wheel pin and retainer pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Electric start button used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig ADD Gasoline See FigIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigTo Adjust Traction Belt and Auger Belt Tension CarburetorFuel System StorageOther Engine OILTroubleshooting Exploded KEY Part Description CARRIAGEBOLT5/16−18X.625 Auger Assembly 30 LHAuger Assembly 30 RH 532 43 59-51 Plate Skid Plastic Hdpe Flange BLKKnob Black 532 18 45-11 Deflector WeldmentStrap POP RivetCable Assembly Heat Shield 532 42 82-72 LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot Bracket532 44 36-17 Pivot Support Weldment Repair Parts Snow Thrower Model P14530ES HandlesHandle Grip Retainer Knob RED 584 80 90-01 Interlock Control RODSpacer Handle Knob01.10.001-B Interlock StopRepair Parts Snow Thrower Model P14530ES Drive Item 42 Exploded817 54 10-08 Thred Rolling Screw Speed Selector AssemblyShifter Link 532 40 26-89 Drive Plate Assembly Wheel HUBRepair Parts Frame 532 42 86-85 Cover Assembly580 42 61-01 LCT Complete Engine KEY Part Description 532 43 07-64 Engine Mounting PlateBelt Guide Idler Pulley 585 20 02-01 Pulley ENG Impeller585 02 93-01 Pulley ENG Traction Washer 5/16Repair Parts Snow Thrower Model P14530ES Wheels Wheel Assembly LHKEY Part Description 532 44 30-59 Safety Ignition KEY KIT Repair Parts Snow Thrower Model P14530ES BAG of PartsPower Cord WrenchRepair Parts Snow Thrower Model P14530ES Decals Service Notes Service Notes Limited Warranty

P14530ES specifications

The Poulan P14530ES is a highly efficient chainsaw designed for homeowners and light-duty professionals who need a reliable tool for various cutting tasks. Featuring a powerful 14-amp motor, this electric chainsaw offers an impressive performance without the hassle of gas and oil. With its lightweight design, which weighs just under 10 pounds, the P14530ES ensures ease of handling and maneuverability, making it ideal for those who may not have extensive experience with chainsaws.

One of the standout features of the Poulan P14530ES is its easy starting system. Unlike traditional gas chainsaws that can be difficult to start, this electric model eliminates the need for pull cords. Users simply plug it in and press a button, allowing for immediate operation. This makes it particularly user-friendly, especially for novice users or those who might struggle with the pull-start mechanisms found in gas-powered saws.

The chainsaw also comes equipped with a 16-inch steel bar and chain, providing ample cutting capacity for tasks such as trimming, pruning, and cutting firewood. The chain itself is designed for low kickback, ensuring a safer cutting experience while still delivering precision and efficiency. The built-in automatic oiler keeps the chain well-lubricated during use, which minimizes wear and extends the tool's lifespan.

Durability is another key characteristic of the Poulan P14530ES. Constructed with high-quality materials, this chainsaw can withstand the rigors of regular use. It also features a transparent oil reservoir, allowing users to easily monitor oil levels and make sure the chain remains properly lubricated.

Safety features are paramount with the P14530ES, which includes a front hand guard and a chain brake to protect users from unexpected kickback. Additionally, the lightweight design reduces operator fatigue, enabling longer periods of use without discomfort.

In summary, the Poulan P14530ES is a solid choice for anyone looking for a dependable electric chainsaw. With its combination of power, ease of use, and safety features, it effectively meets the needs of homeowners and occasional users alike. Whether it's for yard maintenance or firewood preparation, this chainsaw stands out as a practical and efficient tool.
Top Page Image Contents