Poulan P14530ES owner manual To Remove Wheels See Fig, To Adjust Cable Tension See Fig, Carburetor

Page 17

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 21)

Remove the wheel pin and retainer pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- ner most hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower) remove wheel pin and retainer pin from wheel hub and insert wheel pin and retainer into the outer hole in axle only.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WHEEL PIN

OUTER HOLE

 

RETAINER

INNER

HOLE

PIN

 

WHEEL

WHEEL HUB

 

FIG. 21

TO ADJUST CABLE TENSION (See Fig. 22)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 22

TO ADJUST TRACTION BELT AND AUGER BELT TENSION

If the traction or auger belt is slipping because it is not tight enough when engaged, the tension can be increased by adjusting the spring location in the control rod. Unhook the rod from the control lever and move the spring at the bottom of the rod one or two holes closer to the top of the rod. This effectively shortens the rod and increases the belt tension. (See "INSTALL AUGER CONTROL ROD" in the Assembly section of this manual.)

ENGINE

SEE ENGINE MANUAL.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 2,134 meters. If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a service center/department.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a service center/depart- ment, which has the proper equipment and experience to make any necessary adjustments.

17

Image 17
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYElectric start button used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigScraper BAR See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Traction Belt and Auger Belt Tension To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorOther StorageFuel System Engine OILTroubleshooting Exploded KEY Part Description CARRIAGEBOLT5/16−18X.625 Auger Assembly 30 LHAuger Assembly 30 RH Flange BLK 532 43 59-51 Plate Skid Plastic HdpeStrap 532 18 45-11 Deflector WeldmentKnob Black POP RivetCable Assembly Adjustable 532 42 82-72 LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator Pivot Bracket532 44 36-17 Pivot Support Weldment Repair Parts Snow Thrower Model P14530ES HandlesHandle Grip Retainer Spacer 584 80 90-01 Interlock Control RODKnob RED Handle KnobInterlock Stop 01.10.001-BItem 42 Exploded Repair Parts Snow Thrower Model P14530ES DriveShifter Link 532 40 26-89 Drive Plate Assembly Speed Selector Assembly817 54 10-08 Thred Rolling Screw Wheel HUBRepair Parts 580 42 61-01 LCT Complete Engine 532 42 86-85 Cover AssemblyFrame KEY Part Description 532 43 07-64 Engine Mounting Plate585 02 93-01 Pulley ENG Traction Idler Pulley 585 20 02-01 Pulley ENG ImpellerBelt Guide Washer 5/16Wheel Assembly LH Repair Parts Snow Thrower Model P14530ES WheelsPower Cord Repair Parts Snow Thrower Model P14530ES BAG of PartsKEY Part Description 532 44 30-59 Safety Ignition KEY KIT WrenchRepair Parts Snow Thrower Model P14530ES Decals Service Notes Service Notes Limited Warranty

P14530ES specifications

The Poulan P14530ES is a highly efficient chainsaw designed for homeowners and light-duty professionals who need a reliable tool for various cutting tasks. Featuring a powerful 14-amp motor, this electric chainsaw offers an impressive performance without the hassle of gas and oil. With its lightweight design, which weighs just under 10 pounds, the P14530ES ensures ease of handling and maneuverability, making it ideal for those who may not have extensive experience with chainsaws.

One of the standout features of the Poulan P14530ES is its easy starting system. Unlike traditional gas chainsaws that can be difficult to start, this electric model eliminates the need for pull cords. Users simply plug it in and press a button, allowing for immediate operation. This makes it particularly user-friendly, especially for novice users or those who might struggle with the pull-start mechanisms found in gas-powered saws.

The chainsaw also comes equipped with a 16-inch steel bar and chain, providing ample cutting capacity for tasks such as trimming, pruning, and cutting firewood. The chain itself is designed for low kickback, ensuring a safer cutting experience while still delivering precision and efficiency. The built-in automatic oiler keeps the chain well-lubricated during use, which minimizes wear and extends the tool's lifespan.

Durability is another key characteristic of the Poulan P14530ES. Constructed with high-quality materials, this chainsaw can withstand the rigors of regular use. It also features a transparent oil reservoir, allowing users to easily monitor oil levels and make sure the chain remains properly lubricated.

Safety features are paramount with the P14530ES, which includes a front hand guard and a chain brake to protect users from unexpected kickback. Additionally, the lightweight design reduces operator fatigue, enabling longer periods of use without discomfort.

In summary, the Poulan P14530ES is a solid choice for anyone looking for a dependable electric chainsaw. With its combination of power, ease of use, and safety features, it effectively meets the needs of homeowners and occasional users alike. Whether it's for yard maintenance or firewood preparation, this chainsaw stands out as a practical and efficient tool.