Poulan PR624ES Gearbox Assembly, Bearing, Impeller Pulley, Discharge Base, Tool Clip, Plug, Seal

Page 23

REPAIR PARTS SNOW THROWER - - MODEL NO. PR624ES (96192002900)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART
NO.	NO.	DESCRIPTION

1175321X479 IMPELLER

2427148 GEARBOX ASSEMBLY

3	188909	BEARING
4	427146	IMPELLER PULLEY
5	175322	DISCHARGE BASE

6178675X008 CORNER BRACKET

7192199 CLEAN OUT TOOL

8	405400	TOOL CLIP
9	73800400	NUT 1/4-20
10	74780426	SCREW 1/4-20 X .625
11	427942	NUT 5/16-18
12	163183	SCREW 5/16-18 X .625
13	427145	IMPELLER HUB
14	427154	IMPELLER SLEEVE
15	73900600	NUT 3/8-16
16	180355	CARRIAGE BOLT
17	194189	SCREW 13-16 X .625
18	407760	PLUG
19	427302	GEARBOX COVER RH
20	427345	GASKET
21	407770	SEAL
22	407762	BEARING
23	174697	THRUST WASHER 1.00
24	407763	WORM GEAR
25	407764	AUGER SHAFT
26	189282	SQUARE KEY
27	407758	BEARING
28	174683	THRUST WASHER
29	427147	IMPELLER SHAFT
30	7836M	ROLL PIN
31	174681	THRUST WASHER
32	174684	THRUST BEARING
33	407769	BEARING
34	407768	O-RING
35	407767	SCREW 5/16-18 X .750
36	427317	GEARBOX COVER LH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 23

Image 23

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Auger Bearing Auger Housing KEY Part Description Scraper BARSkid Plate RH Auger Assembly LHAuger Assembly RH Skid Plate LHExploded Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool BearingRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldStrap Chute WeldmentDeflector Weldment Deflector SealRepair Parts Snow Thrower - Model NO. PR624ES Handles Interlock CAM Lower TubePivot Support Interlock SpringWasher 3/8 SpacerKnob RED Handle KnobShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPRepair Parts Snow Thrower - Model NO. PR624ES Drive Rubber Ring AssemblyDrive Plate Assembly Speed SelectorClik PIN Axle ShaftRoll PIN 3/16 Sprocket427963X428 Cover AssemblyComplete LCT Engine FrameIdler Pulley Impeller BeltTraction Belt Idler ARM Bracket187866X421 Repair Parts Snow Thrower - Model NO. PR624ES WheelsWheel Assembly LH 187831X421422663 Repair Parts Snow Thrower - Model NO. PR624ES BAG of PartsSafety Ignition KEY DECAL, DANGER, Deflector Repair Parts Snow Thrower - Model NO. PR624ES Decals181037 DECAL, DangerService Notes Service Notes Limited Warranty