Poulan PR624ES owner manual Engine, Cleaning

Page 14

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Scraper BAR Auger HousingKEY Part Description Auger BearingSkid Plate LH Auger Assembly LHAuger Assembly RH Skid Plate RHExploded Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller PulleyCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadDeflector Seal Chute WeldmentDeflector Weldment StrapRepair Parts Snow Thrower - Model NO. PR624ES Handles Interlock Spring Lower TubePivot Support Interlock CAMHandle Knob SpacerKnob RED Washer 3/8Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomRepair Parts Snow Thrower - Model NO. PR624ES Drive Speed Selector AssemblyDrive Plate Assembly Rubber RingSprocket Axle ShaftRoll PIN 3/16 Clik PINFrame Cover AssemblyComplete LCT Engine 427963X428Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley187831X421 Repair Parts Snow Thrower - Model NO. PR624ES WheelsWheel Assembly LH 187866X421422663 Repair Parts Snow Thrower - Model NO. PR624ES BAG of PartsSafety Ignition KEY DECAL, Danger Repair Parts Snow Thrower - Model NO. PR624ES Decals181037 DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

PR624ES specifications

The Poulan PR624ES is a powerful and efficient snow blower designed to tackle the challenges of winter weather. Equipped with a 24-inch clearing width and a robust 6.5 horsepower engine, this machine is ideal for homeowners looking to clear medium to large driveways and sidewalks quickly and effectively.

One of the standout features of the PR624ES is its electric start technology. This convenient feature allows users to start the snow blower with the push of a button, eliminating the struggle of pulling a cord in cold weather. This is particularly beneficial during particularly chilly mornings when you want to get the job done efficiently without unnecessary hassle.

The snow blower features a heavy-duty, steel auger that cuts through snow and ice with exceptional precision. This durable construction ensures long-lasting performance, while the efficient design allows for effective snow removal even in heavy, compacted snow. The auger's design also minimizes clogging, ensuring smooth operation throughout the clearing process.

Another important characteristic of the Poulan PR624ES is its adjustable discharge chute. Users can easily direct the snow up to 40 feet away, allowing for greater control over where the snow is deposited. This feature is especially useful when dealing with large accumulations of snow or when needing to keep areas clear for traffic or pedestrians.

The PR624ES is designed for comfort and usability. It comes with ergonomic handles that provide a comfortable grip, reducing fatigue during extended use. Additionally, the snow blower is equipped with a six-speed transmission, including six forward and two reverse speeds, which allows the user to maneuver through varying snow conditions easily.

Enhancing its capabilities further, the Poulan PR624ES includes a headlight that increases visibility in low-light conditions. This is particularly useful for early morning or late evening snow clearing, ensuring that users can operate safely and effectively.

Overall, the Poulan PR624ES stands out as a reliable and user-friendly snow blower, combining power, efficiency, and thoughtful design features that make winter weather management much easier. With its combination of cutting-edge technologies and practical characteristics, it is an excellent choice for any homeowner dealing with snow-covered pathways and driveways.
Top Page Image Contents