Poulan PR624ES Before Starting the Engine, To Adjust Skid Plates See Fig, Scraper BAR See Fig

Page 11

OPERATION

TO ADJUST SKID PLATES (See Fig. 16)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the hex nuts, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION

 

(LOW GROUND

 

CLEARANCE)

 

 

AUGER

 

HOUSING

 

SCRAPER BAR

HEX

SKID PLATE

NUTS

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 16

SCRAPER BAR (See Fig. 16)

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 17)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 17)

•Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gaso- hol or using ethanol or methanol) can attract moisture which leads to separation and forma- tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

ON / OFF

RECOIL (AUXILIARY)

STARTER HANDLE

SWITCH

 

 

GASOLINE

 

FILLER CAP

CHOKE

ENGINE OIL FILL

CAP / DIPSTICK

CON-

 

TROL

 

 

STARTER

 

BUTTON

SAFETY

 

IGNITION

 

KEY

 

PRIMER

 

 

POWER

 

CORD

FUEL SHUT-OFF VALVE

PLUG

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 17

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Auger Bearing Auger HousingKEY Part Description Scraper BARSkid Plate RH Auger Assembly LHAuger Assembly RH Skid Plate LHExploded Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool BearingRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldStrap Chute WeldmentDeflector Weldment Deflector SealRepair Parts Snow Thrower - Model NO. PR624ES Handles Interlock CAM Lower TubePivot Support Interlock SpringWasher 3/8 SpacerKnob RED Handle KnobShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPRepair Parts Snow Thrower - Model NO. PR624ES Drive Rubber Ring AssemblyDrive Plate Assembly Speed SelectorClik PIN Axle ShaftRoll PIN 3/16 Sprocket427963X428 Cover AssemblyComplete LCT Engine FrameIdler Pulley Impeller BeltTraction Belt Idler ARM Bracket187866X421 Repair Parts Snow Thrower - Model NO. PR624ES WheelsWheel Assembly LH 187831X421422663 Repair Parts Snow Thrower - Model NO. PR624ES BAG of PartsSafety Ignition KEY DECAL, DANGER, Deflector Repair Parts Snow Thrower - Model NO. PR624ES Decals181037 DECAL, DangerService Notes Service Notes Limited Warranty

PR624ES specifications

The Poulan PR624ES is a powerful and efficient snow blower designed to tackle the challenges of winter weather. Equipped with a 24-inch clearing width and a robust 6.5 horsepower engine, this machine is ideal for homeowners looking to clear medium to large driveways and sidewalks quickly and effectively.

One of the standout features of the PR624ES is its electric start technology. This convenient feature allows users to start the snow blower with the push of a button, eliminating the struggle of pulling a cord in cold weather. This is particularly beneficial during particularly chilly mornings when you want to get the job done efficiently without unnecessary hassle.

The snow blower features a heavy-duty, steel auger that cuts through snow and ice with exceptional precision. This durable construction ensures long-lasting performance, while the efficient design allows for effective snow removal even in heavy, compacted snow. The auger's design also minimizes clogging, ensuring smooth operation throughout the clearing process.

Another important characteristic of the Poulan PR624ES is its adjustable discharge chute. Users can easily direct the snow up to 40 feet away, allowing for greater control over where the snow is deposited. This feature is especially useful when dealing with large accumulations of snow or when needing to keep areas clear for traffic or pedestrians.

The PR624ES is designed for comfort and usability. It comes with ergonomic handles that provide a comfortable grip, reducing fatigue during extended use. Additionally, the snow blower is equipped with a six-speed transmission, including six forward and two reverse speeds, which allows the user to maneuver through varying snow conditions easily.

Enhancing its capabilities further, the Poulan PR624ES includes a headlight that increases visibility in low-light conditions. This is particularly useful for early morning or late evening snow clearing, ensuring that users can operate safely and effectively.

Overall, the Poulan PR624ES stands out as a reliable and user-friendly snow blower, combining power, efficiency, and thoughtful design features that make winter weather management much easier. With its combination of cutting-edge technologies and practical characteristics, it is an excellent choice for any homeowner dealing with snow-covered pathways and driveways.
Top Page Image Contents