Poulan owner manual Repair Parts Snow Thrower Model PP291E30 Handles

Page 28

REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)

HANDLES

7	4

	3			5
	2			KEY	PART
	2			NO.	NO.	DESCRIPTION
				NO.	NO.	DESCRIPTION
				1	182906	CONSOLE PANEL
				2	178668	HEADLIGHT BEZEL
	5	4	1	3	180927	FLOOD HEADLIGHT
6		4		4	184471	SHOULDERSCREW10−24X.625
				4	184471	SHOULDERSCREW10−24X.625
				5	175262	SCREW 10−24 X 1.25
				5	175262	SCREW 10−24 X 1.25
				6	178770	WIRE HARNESS
		01.10.007-B		7	183784	BULB
		01.10.007-B

4

			KEY	PART
		3	NO.	NO.	DESCRIPTION
		3	1	412675X004	INTERLOCK SPRING
			1	412675X004	INTERLOCK SPRING
5	2		2	414572	INTERLOCK CAM
5			3	178831	TORSION SPRING
			3	178831	TORSION SPRING
			4	169675	RETAINER
	1		5	17060410	SCREW 1/4−20 X .625
	1		6	421252X004	INTERLOCK STOP
	6	01.08.007-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

28

Image 28

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig To Adjust Skid Plates See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BAR See FigTo USE Drift Cutters See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Auger Housing KEY Part DescriptionScrapper BAR Auger BearingExploded Gearbox Assembly 178675X008 Corner Bracket Clean OUT ToolBearing Impeller PulleyAuger Assembly 30 LH Auger Assembly 30 RHSkid Plate LH Skid Plate RH181160X479 Drift Cutter BAR Plastic WasherKnob Black POP RivetChute Snow Shield Shield Retainer StrapLEVER/CABLE Rotator Assembly Cable Assembly AdjustableRotator Head Rotator Pivot BracketRepair Parts Snow Thrower Model PP291E30 Handles Loop Handle LH Loop Handle RHLower Tube Pivot SupportSpacer Knob REDHandle Knob Washer 3/8Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Repair Parts Snow Thrower Model PP291E30 Drive Assembly Drive Plate AssemblySpeed Selector Rubber RingRepair Parts Axle ShaftRoll PIN 3/16 SprocketCover Assembly Complete LCT EngineFrame 427963X428Impeller Belt Traction BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower Model PP291E30 Wheels Wheel Assembly LH187833X421 187865X421Safety Ignition KEY Repair Parts Snow Thrower Model PP291E30 BAG of Parts422663 Repair Parts Snow Thrower Model PP291E30 Decals DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionLimited Warranty