Poulan PP291E30 owner manual To Remove Wheels See Fig, To Adjust Cable Tension See Fig, Carburetor

Page 18

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 23)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

KLIK PIN	OUTER HOLE
	INNER
	HOLE
WHEEL	WHEEL HUB

FIG. 23

TO ADJUST CABLE TENSION (See Fig. 24)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 24

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 2,134 meters. If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a service center/department.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a service center/depart- ment, which has the proper equipment and experience to make any necessary adjustments.

18

Image 18

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigTo USE Drift Cutters See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Scrapper BAR Auger HousingKEY Part Description Auger BearingExploded Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller PulleySkid Plate LH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate RH181160X479 Drift Cutter BAR Plastic WasherChute Snow Shield Knob BlackPOP Rivet Shield Retainer StrapRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot BracketRepair Parts Snow Thrower Model PP291E30 Handles Lower Tube Loop Handle LHLoop Handle RH Pivot SupportHandle Knob SpacerKnob RED Washer 3/8Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Repair Parts Snow Thrower Model PP291E30 Drive Speed Selector AssemblyDrive Plate Assembly Rubber RingRoll PIN 3/16 Repair PartsAxle Shaft SprocketFrame Cover AssemblyComplete LCT Engine 427963X428Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley187833X421 Repair Parts Snow Thrower Model PP291E30 WheelsWheel Assembly LH 187865X421Repair Parts Snow Thrower Model PP291E30 BAG of Parts Safety Ignition KEY422663 DECAL, DANGER, Deflector Repair Parts Snow Thrower Model PP291E30 DecalsDECAL, Danger DECAL, InstructionLimited Warranty