Poulan PP291E30 Install Traction Drive Control ROD See Figs, Install Auger Control ROD See Figs

Page 6

ASSEMBLY / PRE-OPERATION

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod is installed on the snow thrower.

1.Remove plastic tie securring rod to lower handle.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

PLASTIC TIE

TRACTION DRIVE

CONTROL ROD

VINYL

SLEEVE

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

1.Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. Slide straight rod end through the small hole in the vinyl sleeve. Hook spring in hole in rod end.

2.Hook end of spring into control arm with loop opening up as shown. (See Fig. 5)

3.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

VINYL

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

FIG. 6

6

Image 6

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigTo USE Drift Cutters See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Scrapper BAR Auger HousingKEY Part Description Auger BearingExploded Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller PulleySkid Plate LH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate RH181160X479 Drift Cutter BAR Plastic WasherChute Snow Shield Knob BlackPOP Rivet Shield Retainer StrapRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot BracketRepair Parts Snow Thrower Model PP291E30 Handles Lower Tube Loop Handle LHLoop Handle RH Pivot SupportHandle Knob SpacerKnob RED Washer 3/8Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Repair Parts Snow Thrower Model PP291E30 Drive Speed Selector AssemblyDrive Plate Assembly Rubber RingRoll PIN 3/16 Repair PartsAxle Shaft SprocketFrame Cover AssemblyComplete LCT Engine 427963X428Idler ARM Bracket Impeller BeltTraction Belt Idler Pulley187833X421 Repair Parts Snow Thrower Model PP291E30 WheelsWheel Assembly LH 187865X421Repair Parts Snow Thrower Model PP291E30 BAG of Parts Safety Ignition KEY422663 DECAL, DANGER, Deflector Repair Parts Snow Thrower Model PP291E30 DecalsDECAL, Danger DECAL, InstructionLimited Warranty