Poulan PP291E30 owner manual Loop Handle LH, Loop Handle RH, Lower Tube, Pivot Support

Page 29

REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)

HANDLES

			KEY	PART
4	4		NO.	NO.	DESCRIPTION
4			1	419798X479	LOOP HANDLE LH
4			2	419799X479	LOOP HANDLE RH
		1	2	419799X479	LOOP HANDLE RH
		1	3	74780524	SCREW 5/16−18 X 1.50
			3	74780524	SCREW 5/16−18 X 1.50
3			4	751153	NUT 5/16−18
4
3
2

01.08.004-B

KEY	PART
NO.	NO.	DESCRIPTION
1	419797X479	LOWER TUBE
2	418313X479	PIVOT SUPPORT
3	428867	BOLT 5/16-18 X .750
4	17000616	SCREW 3/8-16 X 1.00

4	4

01.05.004-C

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Image 29

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigScraper BAR See Fig Before Starting the EngineTo USE Drift Cutters See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting KEY Part Description Auger HousingScrapper BAR Auger BearingExploded 178675X008 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller PulleyAuger Assembly 30 RH Auger Assembly 30 LHSkid Plate LH Skid Plate RHPlastic Washer 181160X479 Drift Cutter BARPOP Rivet Knob BlackChute Snow Shield Shield Retainer StrapCable Assembly Adjustable LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketRepair Parts Snow Thrower Model PP291E30 Handles Loop Handle RH Loop Handle LHLower Tube Pivot SupportKnob RED SpacerHandle Knob Washer 3/8Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Repair Parts Snow Thrower Model PP291E30 Drive Drive Plate Assembly AssemblySpeed Selector Rubber RingAxle Shaft Repair PartsRoll PIN 3/16 SprocketComplete LCT Engine Cover AssemblyFrame 427963X428Traction Belt Impeller BeltIdler ARM Bracket Idler PulleyWheel Assembly LH Repair Parts Snow Thrower Model PP291E30 Wheels187833X421 187865X421422663 Repair Parts Snow Thrower Model PP291E30 BAG of PartsSafety Ignition KEY DECAL, Danger Repair Parts Snow Thrower Model PP291E30 DecalsDECAL, DANGER, Deflector DECAL, InstructionLimited Warranty

REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)

KEY

LOOP HANDLE LH

LOOP HANDLE RH

KEY

LOWER TUBE

PIVOT SUPPORT