Poulan PP414EPS30 owner manual Engine, Cleaning

Page 15

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower OperationRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Exploded KEY Part Description Bearing Plug Auger HousingScrapper BAR Auger BearingSkid Plate RH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate LHLockwasher 5/16 Weight BARDrift Cutter BAR Plastic WasherShield Retainer Strap Knob BlackPOP Rivet Chute Snow ShieldRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadRepair Parts Snow Thrower Model PP414EPS30 Handles Pivot Support Loop Handle LHLoop Handle RH Lower TubeWasher 3/8 SpacerKnob RED Handle KnobCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Repair Parts Snow Thrower Model PP414EPS30 Drive Axle ShaftSprocket Exploded Rubber Ring AssemblyDrive Plate Assembly Speed Selector427963X428 Cover AssemblyComplete LCT Engine FrameIdler Pulley Impeller BeltTraction Belt Idler ARM BracketRepair Parts Snow Thrower Model PP414EPS30 Wheels Cable Bracket LH Wheel Assembly LH196752X421 196753X421Repair Parts Snow Thrower Model PP414EPS30 BAG of Parts Safety Ignition KEY422663 DECAL, Instruction Repair Parts Snow Thrower Model PP414EPS30 DecalsDECAL, Danger DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty

PP414EPS30 specifications

The Poulan PP414EPS30 is a powerful and efficient outdoor power tool designed for homeowners and gardening enthusiasts. This chainsaw boasts a variety of features, technologies, and characteristics that make it an excellent choice for both light and heavy-duty applications.

One of the standout features of the Poulan PP414EPS30 is its robust engine. Equipped with a 40cc engine, it delivers ample power to tackle a range of cutting tasks, whether it's felling trees, trimming branches, or cutting firewood. The engine is designed for easy starting and minimal maintenance, thanks to its spring-assisted recoil starter that simplifies the ignition process.

The chainsaw comes with a 16-inch bar and chain, which strike a perfect balance between cutting capacity and maneuverability. This size allows for efficient cutting without being overly cumbersome, making it ideal for homeowners seeking an easy-to-handle tool for their yard maintenance and clean-up needs.

In terms of safety features, the Poulan PP414EPS30 is equipped with an automatic chain oiler that ensures consistent lubrication while in use, prolonging the life of the bar and chain. Additionally, it features a chain brake that quickly stops the chain in case of kickback, enhancing user safety during operation.

The design of the saw prioritizes user comfort, featuring ergonomic handles for a secure grip and reduced vibrations. This is crucial for prolonged use, allowing users to work comfortably without excessive strain. Furthermore, the lightweight construction of the chainsaw means it can be easily maneuvered, reducing fatigue during extended job sessions.

The Poulan PP414EPS30 also incorporates advanced technology such as the Air Filter System, which enhances engine performance and longevity by providing cleaner air intake. This leads to fewer service intervals and prolonged engine life, making it a cost-effective choice in the long run.

Overall, the Poulan PP414EPS30 offers an impressive combination of power, safety, and user-friendly features. With its reliable engine, suitable bar length, and thoughtful design, it stands out as a versatile chainsaw that meets the demands of both occasional users and serious hobbyists alike. Whether for routine yard work or more demanding tasks, this chainsaw is a reliable partner for outdoor maintenance.
Top Page Image Contents