Poulan PP414EPS30 Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 21)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a spacer, shear bolt and hex nut. Should a foreign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever is engaged, check to see if the capscrews have sheared. To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 21

TO REMOVE BELT COVER (See Fig. 22)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

•Replace belt cover by installing cover and screws and tighten securely.

FRAME

BELT COVER

SCREWS

16

FIG. 22

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BAR See FigTo USE Drift Cutters See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Service Notes Exploded KEY Part Description Auger Housing Scrapper BARAuger Bearing Bearing PlugAuger Assembly 30 LH Auger Assembly 30 RHSkid Plate LH Skid Plate RHWeight BAR Drift Cutter BARPlastic Washer Lockwasher 5/16Knob Black POP RivetChute Snow Shield Shield Retainer StrapLEVER/CABLE Rotator Assembly Cable Assembly AdjustableRotator Head Rotator Pivot BracketRepair Parts Snow Thrower Model PP414EPS30 Handles Loop Handle LH Loop Handle RHLower Tube Pivot SupportSpacer Knob REDHandle Knob Washer 3/8Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Axle Shaft Repair Parts Snow Thrower Model PP414EPS30 DriveSprocket Exploded Assembly Drive Plate AssemblySpeed Selector Rubber RingCover Assembly Complete LCT EngineFrame 427963X428Impeller Belt Traction BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower Model PP414EPS30 Wheels Wheel Assembly LH 196752X421196753X421 Cable Bracket LHSafety Ignition KEY Repair Parts Snow Thrower Model PP414EPS30 BAG of Parts422663 Repair Parts Snow Thrower Model PP414EPS30 Decals DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionService Notes Service Notes Limited Warranty

PP414EPS30 specifications

The Poulan PP414EPS30 is a powerful and efficient outdoor power tool designed for homeowners and gardening enthusiasts. This chainsaw boasts a variety of features, technologies, and characteristics that make it an excellent choice for both light and heavy-duty applications.

One of the standout features of the Poulan PP414EPS30 is its robust engine. Equipped with a 40cc engine, it delivers ample power to tackle a range of cutting tasks, whether it's felling trees, trimming branches, or cutting firewood. The engine is designed for easy starting and minimal maintenance, thanks to its spring-assisted recoil starter that simplifies the ignition process.

The chainsaw comes with a 16-inch bar and chain, which strike a perfect balance between cutting capacity and maneuverability. This size allows for efficient cutting without being overly cumbersome, making it ideal for homeowners seeking an easy-to-handle tool for their yard maintenance and clean-up needs.

In terms of safety features, the Poulan PP414EPS30 is equipped with an automatic chain oiler that ensures consistent lubrication while in use, prolonging the life of the bar and chain. Additionally, it features a chain brake that quickly stops the chain in case of kickback, enhancing user safety during operation.

The design of the saw prioritizes user comfort, featuring ergonomic handles for a secure grip and reduced vibrations. This is crucial for prolonged use, allowing users to work comfortably without excessive strain. Furthermore, the lightweight construction of the chainsaw means it can be easily maneuvered, reducing fatigue during extended job sessions.

The Poulan PP414EPS30 also incorporates advanced technology such as the Air Filter System, which enhances engine performance and longevity by providing cleaner air intake. This leads to fewer service intervals and prolonged engine life, making it a cost-effective choice in the long run.

Overall, the Poulan PP414EPS30 offers an impressive combination of power, safety, and user-friendly features. With its reliable engine, suitable bar length, and thoughtful design, it stands out as a versatile chainsaw that meets the demands of both occasional users and serious hobbyists alike. Whether for routine yard work or more demanding tasks, this chainsaw is a reliable partner for outdoor maintenance.
Top Page Image Contents