Poulan PP208E24 owner manual To Replace Belts See Fig

Page 16

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 20)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a service center/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construc- tion and should be replaced by original equipment manu- facturer (OEM) belts available from your nearest service center/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding the auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE HAIRPIN FROM CLUTCH ROD and re- move clutch rod from swing plate. Tip swing plate forward.

7.REMOVE AUGER BELT from around pulley.

8.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

9.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

10.Install clutch rod in swing plate; secure with hairpin.

11.Place auger belt around and inside the groove of auger pulley only.

12.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

13.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

14.Install the two (2) hex bolts and tighten securely.

15.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

16.INSTALL BELT COVER and two (2) screws. Tighten securely.

17.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

BOLT

 

IDLER ARM

 

AUGER

SQUARE

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

 

IDLER ARM

 

 

 

BRACKET

 

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

 

16

FIG. 20

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Electric start button used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting 01.07.004-C KEY Part Description Auger Housing Auger Assembly LHAuger Assembly RH Scrapper BARAuger Bearing Bearing PlugChute Weldment Deflector WeldmentDeflector Seal StrapLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadPanel Bracket LH Panel Bracket RH Handle GripLower Tube Pivot SupportSpacer RetainerKnob RED Handle KnobImpeller ROD Traction RODShifter ROD TOP Shifter ROD BottomConsole Panel Interlock SpringInterlock CAM Torsion SpringRepair Parts Snow Thrower - Model Number PP208E24 Drive Speed Selector Assembly Drive Plate AssemblyWheelhub END PlateAxle Shaft Roll PIN 3/16Sprocket Clik PINCover Assembly Complete LCT EngineFrame 423184X428Impeller Belt Traction BeltIdler ARM Idler Bushing187831X421 Wheel Assembly LH187866X421 Safety Ignition KEY 422663DECAL, Danger DECAL, DANGER, DeflectorDECAL, Instruction DECAL, Auger Lever RTService Notes Service Notes Limited Warranty

PP208E24 specifications

The Poulan PP208E24 is a high-performance gas-powered chainsaw designed to meet the demands of homeowners and professional users alike. Combining efficiency, durability, and ease of use, this model is an excellent choice for those tackling a variety of cutting tasks, including tree pruning, firewood chopping, and general yard maintenance.

One of the standout features of the PP208E24 is its robust 20-inch bar, which provides ample cutting length for felling larger trees and processing logs. This extended reach allows users to accomplish cutting tasks more quickly while maintaining a professional level of control and precision. The chainsaw is powered by a potent 50cc two-stroke engine, delivering strong performance and reliable power. This engine ensures smooth operation, even under heavy load, making it suitable for both domestic and light commercial use.

The design of the Poulan PP208E24 incorporates several advanced technologies aimed at improving user experience. One notable feature is the Easy Start system, which reduces the effort required to start the chainsaw, making it accessible for users of all experience levels. This technology minimizes the pull resistance, allowing for quicker and more comfortable starting.

Safety is a key consideration in the design of the PP208E24. It comes equipped with a chain brake that instantly stops the chain in case of kickback, providing enhanced protection for the operator. Additionally, the chainsaw features a low kickback chain, further decreasing the potential for injuries, and ensuring a safer cutting experience.

Another important characteristic of the Poulan PP208E24 is its lightweight design. Weighing in at approximately 13 pounds, this chainsaw is easy to maneuver and transport, reducing operator fatigue during extended use. Despite its light weight, the unit is solidly constructed, ensuring longevity and resilience over time.

In terms of maintenance, the PP208E24 features a tool-less chain tensioning system, allowing users to quickly adjust the chain without the need for additional tools. This convenience means that users can spend less time on upkeep and more time cutting.

Overall, the Poulan PP208E24 combines power, safety, and user-friendly features, making it a reliable choice for cutting enthusiasts. Whether you're pruning branches or cutting firewood, this chainsaw offers the performance and convenience needed to get the job done efficiently. With its attention to safety and ease of use, the PP208E24 is an investment that will serve users well for years to come.
Top Page Image Contents