Poulan PP208E24 owner manual Troubleshooting

Page 19

TROUBLESHOOTING

See appropriate section in manual unless directed to an authorized service center/department.

PROBLEM

 

CAUSE

 

CORRECTION

Does not start

1.

Fuel shut-off valve (if so

1.

Turn fuel shut-off valve to OPEN position.

 

 

equipped) in OFF position.

 

 

 

2.

Safety ignition key

2.

Insert safety ignition key.

 

 

is not inserted.

 

 

 

3.

Out of fuel.

3.

Fill fuel tank with fresh, clean gasoline.

 

4.

Throttle in STOP position

4.

Move throttle to FAST position

 

5.

Choke in OFF position.

5.

Move to FULL position.

 

6.

Primer not depressed.

6.

Prime as instructed in the Operation section of this manual.

 

7.

Engine is flooded.

7.

Wait a few minutes before restarting, DO NOT prime.

 

8.

Spark plug wire is

8.

Connect wire to spark plug.

 

 

disconnected.

 

 

 

9.

Bad spark plug.

9.

Replace spark plug.

 

10.

Stale fuel.

10.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

11.

Water in fuel.

11.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

 

 

 

 

Loss of power

1.

Spark plug wire loose.

1.

Reconnect spark plug wire.

 

2.

Throwing too much snow.

2.

Reduce speed and width of swath.

 

3.

Fuel tank cap is covered

3.

Remove ice and snow on and around fuel tank cap.

 

 

with ice or snow.

 

 

 

4.

Dirty or clogged muffler.

4.

Clean or replace muffler.

 

 

 

 

 

Engine idles or

1.

Choke is in FULL position.

1.

Move choke to OFF position.

runs roughly

2.

Blockage in fuel line.

2.

Clean fuel line.

 

3.

Stale fuel.

3.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

4.

Water in fuel.

4.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

5.

Carburetor is in need of

5.

Contact an authorized service center/department.

 

 

adjustment or overhaul.

 

 

 

 

 

 

 

Excessive

1.

Loose parts or damaged

1.

Tighten all fasteners. Replace damaged parts. If vibration

vibration

 

augers or impeller.

 

remains, contact an authorized service center/department.

 

 

 

 

 

Recoil starter

1.

Frozen recoil starter.

1.

See “IF RECOIL STARTER HAS FROZEN”

is hard to pull

 

 

 

in the Operation section of this manual.

 

 

 

 

 

Loss of traction

1.

Drive belt is worn.

1.

Check / replace drive belt.

drive / slowing

2.

Drive belt is off of pulley.

2.

Check / reinstall drive belt.

of drive speed

3.

Friction drive wheel is worn.

3.

Contact an authorized service center/department.

 

 

 

 

 

Loss of snow

1.

Auger belt is off of pulley.

1.

Check / reinstall auger belt.

discharge or

2.

Auger belt is worn.

2.

Check / replace auger belt.

slowing of

3.

Clogged discharge chute.

3.

Clean snow chute.

snow discharge

4.

Augers / impeller jammed.

4.

Remove debris or foreign object from augers / impeller.

 

 

 

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerElectric start button used for starting the engine Meets A.N.S.I. Safety RequirementsTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting 01.07.004-C KEY Part Description Scrapper BAR Auger HousingAuger Assembly LH Auger Assembly RHBearing Plug Auger BearingStrap Chute WeldmentDeflector Weldment Deflector SealRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldPivot Support Panel Bracket LH Panel Bracket RHHandle Grip Lower TubeHandle Knob SpacerRetainer Knob REDShifter ROD Bottom Impeller RODTraction ROD Shifter ROD TOPTorsion Spring Console PanelInterlock Spring Interlock CAMRepair Parts Snow Thrower - Model Number PP208E24 Drive END Plate Speed Selector AssemblyDrive Plate Assembly WheelhubClik PIN Axle ShaftRoll PIN 3/16 Sprocket423184X428 Cover AssemblyComplete LCT Engine FrameIdler Bushing Impeller BeltTraction Belt Idler ARM187831X421 Wheel Assembly LH187866X421 422663 Safety Ignition KEYDECAL, Auger Lever RT DECAL, DangerDECAL, DANGER, Deflector DECAL, InstructionService Notes Service Notes Limited Warranty

PP208E24 specifications

The Poulan PP208E24 is a high-performance gas-powered chainsaw designed to meet the demands of homeowners and professional users alike. Combining efficiency, durability, and ease of use, this model is an excellent choice for those tackling a variety of cutting tasks, including tree pruning, firewood chopping, and general yard maintenance.

One of the standout features of the PP208E24 is its robust 20-inch bar, which provides ample cutting length for felling larger trees and processing logs. This extended reach allows users to accomplish cutting tasks more quickly while maintaining a professional level of control and precision. The chainsaw is powered by a potent 50cc two-stroke engine, delivering strong performance and reliable power. This engine ensures smooth operation, even under heavy load, making it suitable for both domestic and light commercial use.

The design of the Poulan PP208E24 incorporates several advanced technologies aimed at improving user experience. One notable feature is the Easy Start system, which reduces the effort required to start the chainsaw, making it accessible for users of all experience levels. This technology minimizes the pull resistance, allowing for quicker and more comfortable starting.

Safety is a key consideration in the design of the PP208E24. It comes equipped with a chain brake that instantly stops the chain in case of kickback, providing enhanced protection for the operator. Additionally, the chainsaw features a low kickback chain, further decreasing the potential for injuries, and ensuring a safer cutting experience.

Another important characteristic of the Poulan PP208E24 is its lightweight design. Weighing in at approximately 13 pounds, this chainsaw is easy to maneuver and transport, reducing operator fatigue during extended use. Despite its light weight, the unit is solidly constructed, ensuring longevity and resilience over time.

In terms of maintenance, the PP208E24 features a tool-less chain tensioning system, allowing users to quickly adjust the chain without the need for additional tools. This convenience means that users can spend less time on upkeep and more time cutting.

Overall, the Poulan PP208E24 combines power, safety, and user-friendly features, making it a reliable choice for cutting enthusiasts. Whether you're pruning branches or cutting firewood, this chainsaw offers the performance and convenience needed to get the job done efficiently. With its attention to safety and ease of use, the PP208E24 is an investment that will serve users well for years to come.
Top Page Image Contents