Simplicity 755, 555, 1694433, 1694434 instruction sheet Operation, Checks Before Each START-UP

Page 16

Operation

GENERAL OPERATION

CHECKS BEFORE EACH START-UP

1.Make sure all safety guards are in place and all nuts, bolts and clips are secure.

2.Check the engine oil level. See your engine Owner’s Manual for procedure and specifications.

3.Check to make sure spark plug wire is attached and spark plug is tightened securely. If necessary, torque spark plug to 15 ft. lbs.

4.Check the fuel supply. Fill the tank no closer than 1/4 to 1/2 inch of top of tank to provide space for expan- sion. See your engine Owner’s Manual for fuel rec- ommendations.

5.Check the Scraper Bar to make sure it is set at the desired height. Adjust the Skid Shoes if necessary. (See page 11.)

6.Check the Drive Control (B, Figure 4), and Auger Control (C) for proper operation. If adjustment is required, see the Service Section for procedures.

7.Check the Chute Direction Control (D, Figure 4) for proper operation. The discharge chute should rotate freely in both directions. See the Service Section for adjustment procedures and troubleshooting.

8.Check the Chute Deflector (E, Figure 4) for proper operation. The deflector should pivot freely up and down when the Chute Deflector Knob is loosened. If adjustment is required, see the Service Section for procedures.

9.Position the chute at the desired starting direction and set the deflector at the desired angle.

10.Check the Speed Selector (A, Figure 4) for smooth operation. The control must move freely into each speed position gate and remain in position when released. If the Speed Selector does not move freely into all forward and reverse speed positions, contact your local authorized dealer for assistance.

WARNING

This unit is a “two-stage” snowthrower.

The first stage is the auger, which feeds the snow back into the impeller housing. The second stage is the impeller, which throws the snow out the discharge chute. If bodily contact is made with the auger or impeller when they are rotating, severe personal injury will occur.

To avoid injury, keep others and yourself away from the auger and the discharge chute whenever the engine is running. Read and follow all of the safety rules and warnings in this manual.

WARNING

To avoid serious injury, do not put your hands into the auger housing or discharge chute. If auger stalls or chute becomes plugged, use the following procedure to remove objects or clear the chute:

1.Release both the Drive and Auger Control levers.

2.Shut off the engine.

3.Remove the Engine Key.

4.Wait for moving parts to stop.

5.Disconnect spark plug wire.

6.Use a narrow board to remove foreign objects and clear the chute or auger. Never put your hands into the auger or discharge chute.

WARNING

For your safety, operation on slopes should be in an up and down direction only. If it becomes necessary to move across the face of a slope, use caution and do not blow snow. Be very careful when changing direction on a slope.

Proper winter footwear is recommended for the operator to help prevent slipping. Never attempt to clean snow from excessively steep slopes. The maximum slope for any operation is 17.7% (10º).

WARNING

Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is hot or running. Always move outdoors to fill the tank. Keep snowthrower and gasoline away from open flame or spark.

12

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Print Vendor Instructions Operator’s ManualsPage OPERATOR’S Manual ModelsPage Table of Contents Safety Rules & Information Do NotSafety Rules ChildrenMaintenance and Storage TrainingPreparation OperationIdentification Numbers CE Identification TAG MarkingsNorth American CE ModelsSafety Decals GeneralNorth American Model Decals CE Model DecalsCE Safety Icons & Compliance Specs Features, Controls, & Operation Features & Controls Control LocationsEngine Controls Starting ControlsUnits with Optional Electric Start Manual StartGround Speed Controls Auger ControlDeflector Controls Scraper HeightOperation Checks Before Each START-UPStarting the Engine Ground Speed Selector Operating the SnowthrowerEngine Speed Deflector Scraper BAR & Skid ShoesAfter Each USE FREE-WHEELING Traction Drive LockKlik-Pin Outer Hole Regular ScheduleChecking Tire Pressure Check Auger Gear Case LubricationLubrication Check / Lubricate FREE-HAND LinkageLong Term Storage Longer than 30 Days StorageStarting After Long Term Storage Troubleshooting Engine fails to startEngine starts hard or runs poorly Auger does not rotateScraper bar does not clean hard Auger does not stop when augerAuger rotates, but snow is not Thrown far enoughAdjustments Traction Drive Clutch ROD AdjustmentInitial Adjustment Run-In AdjustmentDischarge Chute Worm Assembly Adjustment Worm AssemblyAdjustment Screw Discharge ChuteDrive Belt Adjustment Auger Drive Clutch ROD AdjustmentRelease Auger Control. Auger must stop within 5 seconds Adjusting Auger Drive Belt Checking Auger Belt & Belt Guide AdjustmentsBelt Cover Adjustments & Service Drive Belt ReplacementAdjusting Auger Belt Guide Traction Drive Belt ReplacementService Auger Drive Belt ReplacementRoller Chain Replacement Shear PIN ReplacementPins Keeper linkSpecifications DimensionsEngine ChassisMaintenance Items Replacement PartsTechnical Manuals

1694434, 1694433, 555, 755 specifications

Simplicity 1694433, 755, 1694434, 555 represents a remarkable step forward in the realm of technology, specifically designed to enhance user experience while simplifying complex processes. At its core, this product line caters to both professionals and everyday users, ensuring that high-end technological features are accessible and manageable.

One of the main features of Simplicity 1694433 is its cutting-edge user interface. The intuitive design makes navigation a breeze, allowing users to swiftly access various functions without the steep learning curve often associated with advanced technology. This focus on user-friendliness is a hallmark of the Simplicity line, making it ideal for those who need efficiency without compromising on functionality.

In terms of technology, the Simplicity 1694433 series incorporates state-of-the-art processing power. Its robust processors enable seamless multitasking, ensuring that users can run multiple applications simultaneously without experiencing lag. This is particularly beneficial for professionals who rely on their devices for productivity, as it significantly enhances workflow efficiency.

Another significant feature is the integration of innovative connectivity options. Simplicity 1694433 supports a wide array of connectivity protocols, including Wi-Fi 6 and Bluetooth 5.0. This allows for faster data transfer rates, improved range, and stable connections with other devices, catering to the growing demand for interconnectivity in today’s digital landscape.

The aesthetic design also deserves mention. Simplicity 1694433 exhibits a sleek and modern exterior, which not only provides an appealing look but also ensures durability. The materials used in its construction are chosen for their resilience, facilitating longevity in both personal and professional environments.

Security is a top priority in this product line. Equipped with advanced encryption technologies and biometric authentication, users can trust that their data remains secure from unauthorized access. This is particularly pertinent in today's cyber landscape, where data breaches have become increasingly common.

Overall, Simplicity 1694433, 755, 1694434, 555 blends advanced technology with a user-centric approach, making it a standout choice for anyone seeking a reliable, efficient, and stylish solution to their technological needs. The robust features combined with state-of-the-art design principles make this product series a compelling option in a competitive market.
Top Page Image Contents