Simplicity 1694433, 755 Adjustments & Service, Drive Belt Replacement, Adjusting Auger Belt Guide

Page 30

Adjustments & Service

DRIVE BELT ADJUSTMENT (Continued)

Adjusting Auger Belt Guide

1.With the Auger Control still fully depressed, adjust the Auger Belt Guide so that there is a 1/64” gap (1/32” Maximum) between the end of the guide and the belt (Figure 27), making certain the guide is NOT putting pressure on the belt.

2.Making certain the Auger Belt Guide does NOT move while doing so, tighten the Auger Belt Guide Screw (Figure 27) to secure the guide.

3.Check the adjustment on the Auger Belt Guide (Figure 27) to make certain that the gap between the belt and the belt guide is correct.

4.Disengage the Auger Control by removing the card- board tube (or other means used to temporarily secure the control.)

5.Test the unit by following the steps under the “Checking Auger Belt & Belt Guide Adjustments” above.

WARNING

Failure to properly adjust the Auger Belt Guide may cause auger to rotate when Auger Control has not been depressed.

Belt Guide

& Gap

Belt Guide

Screw

Figure 27. Auger Belt Guide Adjustment

DRIVE BELT REPLACEMENT

The snowthrower has two drive belts, one for the Traction Drive—which transmits engine power to the wheels, and a second for the Auger Drive—which trans- mits engine power to the auger mechanism.

Each of these drive belts are of special construction and should be replaced only with Genuine Replacement Belts which match the original equipment belts. These are available from your dealer. (See COMMON REPLACEMENT PARTS at the back of this manual for the correct part numbers for each of the belts.)

Traction Drive Belt Replacement

1.Disconnect spark plug wire and fasten it away from the spark plug.

2.Remove belt cover.

3.Pull the traction drive belt idler pulley arm (See Figure 23) away from the belt to relieve tension, and slide the belt off the engine pulley.

4.Slip the belt off from around the traction pulley (See Figure 28) and pull the belt out of the unit between the auger pulley and the traction pulley (the lower cover need not be removed for this step).

5.Reverse the procedure to install the new belt. Be sure there are no twists in the belt, and that the belt is properly seated in the pulley grooves.

6.Replace the belt cover.

WARNING

Snowthrower must move only when the traction Drive Control is depressed, and must stop when the lever is released (disengaged).

Traction Drive Belt & Pulley

Figure 28. Traction Drive Pulley

(Lower Cover Removed For Clarity)

7.Start the unit, and check the traction drive for proper operation. See "Traction Clutch Rod Adjustment" for adjustment procedures.

26

Image 30
Contents Print Vendor Instructions Operator’s ManualsPage OPERATOR’S Manual ModelsPage Table of Contents Safety Rules & Information Do NotSafety Rules ChildrenPreparation Maintenance and StorageTraining OperationNorth American Identification NumbersCE Identification TAG Markings CE ModelsNorth American Model Decals Safety DecalsGeneral CE Model DecalsCE Safety Icons & Compliance Specs Features, Controls, & Operation Features & Controls Control LocationsUnits with Optional Electric Start Engine ControlsStarting Controls Manual StartDeflector Controls Ground Speed ControlsAuger Control Scraper HeightOperation Checks Before Each START-UPStarting the Engine Operating the Snowthrower Ground Speed SelectorEngine Speed Deflector Scraper BAR & Skid ShoesFREE-WHEELING Traction Drive Lock After Each USEKlik-Pin Outer Hole Checking Tire Pressure RegularSchedule Check Auger Gear Case LubricationLubrication Check / Lubricate FREE-HAND LinkageStorage Long Term Storage Longer than 30 DaysStarting After Long Term Storage Engine starts hard or runs poorly TroubleshootingEngine fails to start Auger does not rotateAuger rotates, but snow is not Scraper bar does not clean hardAuger does not stop when auger Thrown far enoughInitial Adjustment AdjustmentsTraction Drive Clutch ROD Adjustment Run-In AdjustmentAdjustment Screw Discharge Chute Worm Assembly AdjustmentWorm Assembly Discharge ChuteAuger Drive Clutch ROD Adjustment Drive Belt AdjustmentRelease Auger Control. Auger must stop within 5 seconds Checking Auger Belt & Belt Guide Adjustments Adjusting Auger Drive BeltBelt Cover Adjusting Auger Belt Guide Adjustments & ServiceDrive Belt Replacement Traction Drive Belt ReplacementService Auger Drive Belt ReplacementPins Roller Chain ReplacementShear PIN Replacement Keeper linkEngine SpecificationsDimensions ChassisReplacement Parts Maintenance ItemsTechnical Manuals

1694434, 1694433, 555, 755 specifications

Simplicity 1694433, 755, 1694434, 555 represents a remarkable step forward in the realm of technology, specifically designed to enhance user experience while simplifying complex processes. At its core, this product line caters to both professionals and everyday users, ensuring that high-end technological features are accessible and manageable.

One of the main features of Simplicity 1694433 is its cutting-edge user interface. The intuitive design makes navigation a breeze, allowing users to swiftly access various functions without the steep learning curve often associated with advanced technology. This focus on user-friendliness is a hallmark of the Simplicity line, making it ideal for those who need efficiency without compromising on functionality.

In terms of technology, the Simplicity 1694433 series incorporates state-of-the-art processing power. Its robust processors enable seamless multitasking, ensuring that users can run multiple applications simultaneously without experiencing lag. This is particularly beneficial for professionals who rely on their devices for productivity, as it significantly enhances workflow efficiency.

Another significant feature is the integration of innovative connectivity options. Simplicity 1694433 supports a wide array of connectivity protocols, including Wi-Fi 6 and Bluetooth 5.0. This allows for faster data transfer rates, improved range, and stable connections with other devices, catering to the growing demand for interconnectivity in today’s digital landscape.

The aesthetic design also deserves mention. Simplicity 1694433 exhibits a sleek and modern exterior, which not only provides an appealing look but also ensures durability. The materials used in its construction are chosen for their resilience, facilitating longevity in both personal and professional environments.

Security is a top priority in this product line. Equipped with advanced encryption technologies and biometric authentication, users can trust that their data remains secure from unauthorized access. This is particularly pertinent in today's cyber landscape, where data breaches have become increasingly common.

Overall, Simplicity 1694433, 755, 1694434, 555 blends advanced technology with a user-centric approach, making it a standout choice for anyone seeking a reliable, efficient, and stylish solution to their technological needs. The robust features combined with state-of-the-art design principles make this product series a compelling option in a competitive market.