Simplicity 555 Auger rotates, but snow is not, Thrown far enough, Scraper bar does not clean hard

Page 25

 

 

 

 

 

Troubleshooting

 

 

 

 

 

 

 

 

 

 

 

PROBLEM

 

POSSIBLE CAUSE

 

REMEDY

 

 

 

 

 

Auger rotates, but snow is not

1.

Chute deflector too low.

1.

Adjust deflector as necessary.

thrown far enough

2.

Engine speed too slow.

2.

Set speed to full throttle.

 

3.

Ground speed too fast.

3.

Use slower Speed Selector setting.

 

4.

Snowthrower discharge chute clogged.

4.

STOP engine and REMOVE the key.

 

 

 

 

DISCONNECT the spark plug wire.

 

 

 

 

Clear auger using a narrow board.

 

 

 

 

See warning in SAFETY RULES.

 

5.

Auger belt loose or worn.

5.

Check Auger Drive Belt Adjustment

 

 

 

 

 

Scraper bar does not clean hard

1.

Skid Shoes improperly adjusted.

1.

RAISE Skid Shoes (this lowers the

surface.

 

 

 

Scraper Bar).

 

 

 

 

 

Scraper bar picks up and throws

1.

Skid shoes improperly adjusted.

1.

LOWER Skid Shoes (this raises the

stones on gravel drive.

 

 

 

scraper bar.)

 

 

 

 

 

Poor traction

1.

Tires slipping.

1.

Check tire pressure and tread.

 

 

 

 

 

Auger does not stop when auger

1.

Auger clutch rod too tight or bent.

1.

Loosen or straighten clutch rod.

lever is released

2.

Auger drive belt out of adjustment.

2.

Adjust auger belt.

 

3.

Auger belt guide out of adjustment.

3.

Adjust auger belt guide.

 

 

 

 

 

Snowthrower does not stop when

1.

Traction drive clutch rod bent or too

1.

Loosen rod to remove slack or

drive lever is released

 

tight.

 

replace. See adjustment procedure.

 

 

 

 

 

Snowthrower does not drive when

1.

Traction drive clutch rod loose.

1.

Tighten to remove slack. See adjust-

drive lever is engaged.

 

 

 

ment procedure.

 

2.

Drive belt loose, broken, or stretched.

2.

Replace drive belt.

 

3.

Drive roller chain damaged.

3.

Replace chain.

 

4.

Traction Lock Pins in Free-Wheeling

4.

Change Traction Lock Pins to INNER

 

 

position (OUTER hole).

 

hole to engage traction drive.

 

 

 

 

 

Discharge control is difficult to

1.

Gearing needs lubrication

1.

Oil or grease as required.

operate.

2.

Worm gear not adjusted properly.

2.

Adjust worm gear. See adjustment

 

 

 

 

procedure.

 

3.

Control rod gears misaligned.

3.

Adjust gear bracket. See adjustment

 

 

procedure.

 

 

 

 

 

 

 

 

 

Snowthrower veers to one side.

1.

Tires pressure not equal.

1.

Check tire pressure.

 

2.

One wheel is set in Free-Wheeling

2.

Make certain BOTH Traction Lock

 

 

mode. (Traction Lock Pin is in the

 

Pins are in the INNER holes (to

 

 

OUTER hole).

 

engage traction drive).

 

 

 

 

Excessive vibration.

1. Loose parts or damaged auger.

1.

STOP engine and REMOVE the key.

 

 

 

 

DISCONNECT the spark plug wire.

 

 

 

 

Tighten all hardware. Replace auger

 

 

 

 

if necessary. If vibration continues,

 

 

 

 

see your dealer.

 

 

 

 

 

Drive fails to move snowthrower

1.

Traction Drive out of adjustment.

1.

Readjust drive, or shift Speed

at slow speeds.

 

 

 

Selector setting up one speed faster.

 

 

 

 

 

 

21

Image 25
Contents Operator’s Manuals Print Vendor InstructionsPage Models OPERATOR’S ManualPage Table of Contents Do Not Safety Rules & InformationChildren Safety RulesTraining Maintenance and StoragePreparation OperationCE Identification TAG Markings Identification NumbersNorth American CE ModelsGeneral Safety DecalsNorth American Model Decals CE Model DecalsCE Safety Icons & Compliance Specs Features, Controls, & Operation Control Locations Features & ControlsStarting Controls Engine ControlsUnits with Optional Electric Start Manual StartAuger Control Ground Speed ControlsDeflector Controls Scraper HeightChecks Before Each START-UP OperationStarting the Engine Ground Speed Selector Operating the SnowthrowerEngine Speed Scraper BAR & Skid Shoes DeflectorAfter Each USE FREE-WHEELING Traction Drive LockKlik-Pin Outer Hole Schedule RegularChecking Tire Pressure Check Auger Gear Case LubricationCheck / Lubricate FREE-HAND Linkage LubricationLong Term Storage Longer than 30 Days StorageStarting After Long Term Storage Engine fails to start TroubleshootingEngine starts hard or runs poorly Auger does not rotateAuger does not stop when auger Scraper bar does not clean hardAuger rotates, but snow is not Thrown far enoughTraction Drive Clutch ROD Adjustment AdjustmentsInitial Adjustment Run-In AdjustmentWorm Assembly Discharge Chute Worm Assembly AdjustmentAdjustment Screw Discharge ChuteDrive Belt Adjustment Auger Drive Clutch ROD AdjustmentRelease Auger Control. Auger must stop within 5 seconds Adjusting Auger Drive Belt Checking Auger Belt & Belt Guide AdjustmentsBelt Cover Drive Belt Replacement Adjustments & ServiceAdjusting Auger Belt Guide Traction Drive Belt ReplacementAuger Drive Belt Replacement ServiceShear PIN Replacement Roller Chain ReplacementPins Keeper linkDimensions SpecificationsEngine ChassisMaintenance Items Replacement PartsTechnical Manuals

1694434, 1694433, 555, 755 specifications

Simplicity 1694433, 755, 1694434, 555 represents a remarkable step forward in the realm of technology, specifically designed to enhance user experience while simplifying complex processes. At its core, this product line caters to both professionals and everyday users, ensuring that high-end technological features are accessible and manageable.

One of the main features of Simplicity 1694433 is its cutting-edge user interface. The intuitive design makes navigation a breeze, allowing users to swiftly access various functions without the steep learning curve often associated with advanced technology. This focus on user-friendliness is a hallmark of the Simplicity line, making it ideal for those who need efficiency without compromising on functionality.

In terms of technology, the Simplicity 1694433 series incorporates state-of-the-art processing power. Its robust processors enable seamless multitasking, ensuring that users can run multiple applications simultaneously without experiencing lag. This is particularly beneficial for professionals who rely on their devices for productivity, as it significantly enhances workflow efficiency.

Another significant feature is the integration of innovative connectivity options. Simplicity 1694433 supports a wide array of connectivity protocols, including Wi-Fi 6 and Bluetooth 5.0. This allows for faster data transfer rates, improved range, and stable connections with other devices, catering to the growing demand for interconnectivity in today’s digital landscape.

The aesthetic design also deserves mention. Simplicity 1694433 exhibits a sleek and modern exterior, which not only provides an appealing look but also ensures durability. The materials used in its construction are chosen for their resilience, facilitating longevity in both personal and professional environments.

Security is a top priority in this product line. Equipped with advanced encryption technologies and biometric authentication, users can trust that their data remains secure from unauthorized access. This is particularly pertinent in today's cyber landscape, where data breaches have become increasingly common.

Overall, Simplicity 1694433, 755, 1694434, 555 blends advanced technology with a user-centric approach, making it a standout choice for anyone seeking a reliable, efficient, and stylish solution to their technological needs. The robust features combined with state-of-the-art design principles make this product series a compelling option in a competitive market.