MTD 644E, 664G manual Operating Your Snow Thrower

Page 12

•Crank clockwise to discharge to the left.

•Crank counterclockwise to discharge to the right.

Clean-Out Tool

WARNING: Never use your hand to clear a clogged discharged chute. Shut off engine and remain behind handles until all moving parts have stopped before unclogging.

The chute clean-out tool is fastened to the top of the auger housing with a mounting clip. The tool is designed to clear a clogged discharged chute. Refer to Operating Your Snow Thrower section for more detailed information regarding the chute clean-out tool. See Figure 16.

NOTE: This item is fastened with a cable tie to the rear of the Auger Housing at the factory. Cut the cable tie before operating the snow thrower.

Safety Ignition Key

The safety ignition key must be fully inserted in the switch before the unit will start. Remove the ignition key when the snow thrower is not in use. See Figure 16.

IMPORTANT: Do NOT “turn” the ignition key in an attempt to start the engine. Doing so may cause it to break.

Fuel Shut-off Valve (Optional Equipment)

On models so equipped, the fuel shut-off valve, located under fuel tank, controls fuel-flow from the gas tank. See Figure 16.

Skid Shoe

The position of the skid shoe is determined by the condition of the ground from where snow has to be removed. See Figure 16.

Throttle Control

The throttle control is located on the engine. It regulates the speed of the engine and will shut off the engine when pushed down completely. See Figure 16.

SECTION 5: OPERATING YOUR SNOW THROWER

Before Starting

WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating.

Gas & Oil Fill-Up

Service the engine with gasoline and oil as instructed in the separate engine manual packed with your snow thrower. Read instructions carefully.

WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.

•A plastic cup is provided inside the fuel fill opening on the fuel tank. Remove and discard this cup before filling up the tank. Use the separate fuel tank cap to close after fill-up.

To Start Engine

•Attach spark plug wire to spark plug. Make certain the metal loop on the end of the spark plug wire (inside the boot) is fastened securely over the metal tip on the spark plug.

•Make certain the fuel shut-off valve, if so equipped, is in the OPEN (vertical) position.

•Make certain the auger and drive clutch levers are in the disengaged (released) position.

•Move throttle control up to FAST position. Insert ignition key into slot. Make sure it snaps into place. Do not turn key.

NOTE: Engine will not start unless ignition key is inserted into ignition slot in carburetor cover.

Electric Starter (If Equipped)

•Determine that your house wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain.

•If your house wiring system is not a three-wire grounded system, do not use this electric starter under any conditions.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operator’s Manual Table of Contents Important Safe Operation Practices TrainingMaintenance and Storage Contents of Hardware Pack Boxed Units Assembling Your Snow Thrower UnpackingLoose Parts Boxed Unit CrateAttaching Handle Assembly Assembly Crated UnitAttaching Shift Rod Hardware D Attaching the Chute Assembly Hardware F Attaching Clutch CablesAttaching The Chute Directional Control Know Your Snow Thrower Shift LeverAuger Drive Control Traction ControlOperating Your Snow Thrower To Stop Engine To Engage DriveTo Engage Augers Recoil StarterChute Clean-Out Tool Drift Cutters If EquippedOperating Tips Making Adjustments Traction Control and Shift LeverChute Assembly Adjusting Shift RodAuger Control Skid ShoesMaintaining Your Snow Thrower Drive WheelsLubrication Servicing Your Snow Thrower EngineShave Plate and Skid Shoes Belt Removal and Replacement AugersAuger Belts Friction Wheel Rubber Off-Season StorageDrive Belt Trouble Shooting Guide Trouble Possible Causes Corrective ActionModels 614E, 644E, & 664G Models 614E, 644E, & 664G Part DescriptionModels 614E, 644E, & 664G Jam Lock Nut 3/8-24 Compression Spring 736-0105 Drive Clutch Cable Auger Clutch Wheels Models 614E, 644E, & 664G Models 614E Models 644E & 664G 1615Size Page MANUFACTURER’S Limited Warranty for

664G, 644E specifications

The MTD 644E and 664G tractors represent a significant leap in agricultural technology and efficiency, designed for diverse farming applications. Known for their robust build and advanced features, these models cater to both small and large-scale agricultural operations.

Starting with the MTD 644E, it is powered by a state-of-the-art diesel engine, providing a reliable performance that enhances productivity. The engine delivers impressive horsepower, allowing farmers to tackle various tasks effortlessly. Its fuel efficiency is a standout feature, ensuring reduced operational costs while still meeting demanding farm requirements. The 644E also features a compact design, making it highly maneuverable in tight spaces while maintaining a sturdy construction that guarantees durability in rugged conditions.

On the other hand, the MTD 664G offers slightly higher horsepower, making it suitable for more intensive agricultural work. This model is equipped with a more advanced engine management system that optimizes performance and fuel consumption, ensuring that farmers can work longer hours without frequent refueling. The 664G’s larger frame accommodates additional implements, expanding its versatility for tasks including plowing, tilling, and harvesting.

Both models are built with user-friendly controls, allowing operators to focus on their tasks without unnecessary distractions. The ergonomic seating and intuitive interface are designed to minimize fatigue during long working days. Additionally, these tractors come with a range of safety features, including effective braking systems and visibility enhancements that prioritize operator safety.

Technologically, both the 644E and 664G incorporate precision farming features that allow for better resource management. Implement compatibility enables seamless integration with various agricultural tools, giving users flexibility in their operations. Regular software updates ensure that the tractors remain at the forefront of agricultural technology, further enhancing performance and efficiency.

In summary, the MTD 644E and 664G tractors are tailored for modern farmers seeking reliability and efficiency. Their powerful engines, compact designs, and cutting-edge technology make them indispensable tools on any farm, capable of handling a multitude of agricultural tasks with ease and precision.
Top Page Image Contents