MTD 611 manual Important Safe Operation Practices, Training, Preparation

Page 2

SECTION 1: IMPORTANT SAFE OPERATION PRACTICES

WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR SNOW THROWER. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL- HEED ITS WARNING.

WARNING: The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

DANGER: Your snow thrower was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. If you violate any of these rules, you may cause serious injury to yourself or others.

1. TRAINING

Read this operator's manual carefully in its entirety before attempting to assemble or operate this machine. Be completely familiar with the controls and the proper use of this machine before operating it. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

Never allow children under 14 years old to operate a snow thrower. Children 14 years old and over should only operate snow thrower under close parental supervision. Only persons well acquainted with these rules of safe operation should be allowed to use your snow thrower.

No one should operate this unit while intoxicated or while taking medication that impairs the senses or reactions.

Keep the area of operation clear of all persons, especially small children and pets.

Exercise caution to avoid slipping or falling, especially when operating in reverse.

1.PREPARATION

Thoroughly inspect the area where the equipment is to be used and remove all door mats, sleds, boards, wires and other foreign objects.

Disengage all clutches and shift into neutral before starting engine.

Do not operate equipment without wearing adequate winter outer garments. Do not wear jewelry, long scarfs or other loose clothing which could become entangled in moving parts. Wear footwear which will improve footing on slippery surfaces.

Before working with gasoline, extinguish all cigarettes and other sources of ignition. Check the fuel before starting the engine. Gasoline is an extremely flammable fuel. Do not fill the gasoline tank indoors, while the engine is running, or until engine has been allowed to cool at least two minutes. Replace gasoline cap securely and wipe off any spilled gasoline before starting the engine as it may cause a fire or explosion.

Use a grounded three wire plug-in for all units with electric drive motors or electric starting motors.

Adjust collector housing height to clear gravel or crushed rock surface.

Never attempt to make any adjustments while engine is running (except where specifically recommended by manufacturer).

Let engine and machine adjust to outdoor temperature before starting to clear snow.

Always wear safety glasses or eye shields during operation or while performing an adjustment or repair, to protect eyes from foreign objects that may be thrown from the machine in any direction.

2.OPERATION

Do not put hands or feet near or under rotating parts. Keep clear of discharge opening and auger at all times.

Exercise extreme caution when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic. Do not carry passengers.

After striking a foreign object, stop the engine, remove wire from spark plug, and thoroughly inspect the snow thrower for any damage. Repair the damage before restarting and operating the snow thrower.

2

Image 2
Contents Important Read Safety Rules and Instructions Carefully MTD Products INC. P.O. BOX 368022 CLEVELAND, OhioPreparation Important Safe Operation PracticesTraining OperationMaintenance and Storage Finding Your Model Number Calling Customer SupportContents of Hardware Pack Unpacking Assembly InstructionsTools Required for Assembly Loose Parts in Carton See FigureAttaching the Handles Hardware a Attaching the Clutch GripsAttaching the Clutch Cables Attaching the Handle PanelAttaching Speed Selector Plate and Shift Lever Hardware D Attaching the Chute Assembly Hardware F Attaching the Chute Crank Hardware GAdjusting the Skid Shoes Final Assembly and AdjustmentsTraction Drive Clutch and Shift Lever Adjustment Auger Drive ClutchControls Electric Starter OperationBefore Starting GAS and OIL FILL-UPTo Engage Augers To Stop EngineTo Engage Drive Operating TipsAdjustments Maintenance LubricationBelt Removal and Replacement Auger Belts Drive Belt Changing the Friction Wheel RubberOFF-SEASON Storage Trouble Shooting Guide Model Part Description QTY Model Wheel Assembly Part Description QTY 736-0331 Page Page MANUFACTURER’S Limited Warranty for