Snapper E11305, E9265 important safety instructions Maintenance and Storage

Page 3

IMPORTANT SAFETY INSTRUCTIONS

OPERATIONAL PRECAUTIONS

(Continued From Previous Page)

7.DO NOT put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

8.Start engine only where exhaust fumes will be safely dissipated. Allow a brief warm-up period, and practice operation of controls outside before putting the machine to work.

9.After striking a foreign object, STOP the engine (motor), remove the key, and remove the wire from spark plug. Thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

10.STOP the engine if the machine starts to vibrate excessively as this normally indicates mechanical problems. Remove the key and disconnect the spark plug wire to prevent unintentional starting before servicing or repairing the machine.

11.DO NOT clear snow across the face of slopes. Exercise extreme CAUTION when changing direction on slopes. DO NOT attempt to clear steep slopes.

12.DO NOT leave machine unattended with the engine running. STOP engine and remove key to prevent unauthorized operation.

13.Release clutch control and make sure auger/impeller has STOPPED before adjusting deflector, or placing hands near auger/impeller.

14.DO NOT use snow thrower on surfaces above ground level, such as, a roof of a building.

15.Exercise extreme CAUTION when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

16.DO NOT overload the machine capacity by attempting to clear snow at too fast a rate.

17.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when backing.

18.Disengage power to the auger/impeller when snow thrower is transported or not in use.

19.Use only attachments and accessories approved by the manufacturer of the snow

thrower (such as wheels weights, counterweights, cabs and the like).

20.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

MAINTENANCE AND STORAGE

1.DO NOT store machine or fuel container inside where fumes may reach an open flame, spark, or pilot light as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of reach of children in a well ventilated, unoccupied building.

2.Keep machine and engine free of excess oil, grease and spilled fuel to reduce fire hazard.

3.When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.

4.Inspect all bolts, nuts and screws frequently and keep properly tightened.

5.Use only recommended shear bolts (if equipped) to prevent possible damage to machine.

6.Service engine and make adjustments only when engine is stopped. Remove key, remove wire from spark plug, secure wire away from plug, and disconnect cord from electric starting motors to prevent accidental starting.

7.DO NOT change engine governor speed settings or overspeed engine.

8.DO NOT test for spark by grounding the spark plug next to spark plug hole. Spark from the plug could ignite gas exiting engine.

9.Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices.

10.Use only genuine SNAPPER replacement parts to assure that original standards are maintained.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Model Number Explanation Model Designation Series Designation Engine HP Auger WidthInstruction No -3336 I.R /14/00 Operational Precautions Protection for ChildrenPreparation Maintenance and Storage Table of Contents European Community Hearing Protection Required Forward Reverse Ground Speed ControlRabbit / Fast Turtle / Slow Neutral Year of Manufacture Safety Instructions to Prevent Injury Nomenclature IntroductionPRE-START Check List Minimum Gauge for Cord SetsGo to Page 11 for Electric Start Models Engine STARTING, Operation & Stopping Recoil Start ModelsDischarge Chute and Deflector Adjustment Engaging AugerEngaging Wheel Drive STARTING, Operation & Stopping Electric Start Models Free Wheel Machine Stopping ENGINE, Auger & Wheel DriveCheck Wheel Drive Belt Service After First 5 Hours Check Auger Drive BeltGeneral Lubrication Gear CASE, Auger Shaft and Auger Bearing LubricationEngine Spark Plug Storage ProcedureMaintenance and Service Parts Annually END of Each SeasonAuger Belt Adjustment Idler Pulley Adjustment Auger and Drive Belt Adjustment Cable AdjustmentRecheck cable for proper extension Reinstall belt cover Repair & Adjustments Skid Shoe Adjustment Single Handle Control Adjustment Rubber Drive Tire Replacement Chute Crank AdjustmentUSE HRS Season Problem Probable Cause Corrective ActionService Performed Each 100Disclaimer of Warranty Year Limited WarrantyPage European TWO Stage Large Frame Snow Thrower Series
Related manuals
Manual 28 pages 34.11 Kb

E11305, E9265 specifications

Snapper E9265, 10305E, 8265, E10305E, and E11305 are part of an innovative line of electric snapper products designed to provide robust performance and versatility across various applications. These models represent the intersection of advanced technology and user-centric design, catering to both professionals and DIY enthusiasts.

One of the main features of these snapper models is their powerful motor. With high torque output, these devices can effortlessly tackle challenging materials, ensuring efficient operation in a range of conditions. This motor is engineered for durability and longevity, minimizing the need for maintenance while maximizing productivity.

The E9265 and E10305E feature cutting-edge brushless motor technology, which not only enhances performance but also increases energy efficiency. This feature is particularly beneficial for users who prioritize sustainability and seek to reduce their carbon footprint. The brushless motor extends the life of the tool and is quieter in operation compared to traditional brushed motors, making it ideal for use in residential areas or noise-sensitive environments.

Additionally, these models come equipped with advanced battery technology, featuring lithium-ion power packs that provide longer runtime and faster charging capabilities. Users can enjoy extended working periods without the anxiety of running out of power mid-task. The snapper line also integrates intelligent battery management systems that monitor charge levels and optimize power usage, prolonging battery life.

In terms of user experience, the Snapper E9265, 10305E, and other variants boast ergonomic designs that prioritize comfort and control. Anti-vibration handles reduce user fatigue during prolonged use, while variable speed settings allow for a customizable approach to different tasks. The lightweight construction of these tools enhances maneuverability, making them suitable for both heavy-duty applications and delicate work.

In addition to performance and comfort, safety features are a top priority in these models. Equipped with automatic shut-off functions and protective casing, the snapper tools ensure that users can operate them with confidence. This attention to safety doesn't compromise on efficiency, as these tools are built to deliver precise and powerful results.

Overall, the Snapper E9265, 10305E, 8265, E10305E, and E11305 embody a perfect blend of technology, performance, and user-friendly design. They are engineered to exceed the expectations of users across various fields, from construction to home improvement, making them a valuable addition to any toolkit. Whether you are a seasoned professional or a weekend warrior, Snapper offers a reliable solution that meets the demands of modern projects.
Top Page Image Contents