Snapper E11305, E9265 STARTING, Operation & Stopping Electric Start Models

Page 11

Section 2 - OPERATING INSTRUCTIONS

2.2STARTING, OPERATION & STOPPING (RECOIL START MODELS)

2.2.6. STOPPING - ENGINE, AUGER & WHEEL

DRIVE

Stop the auger/impeller and wheel drive by releasing the auger/impeller and wheel drive control levers. Stop the engine by moving the engine speed control to the stop position or removing the key from the switch. Always remove key from key switch before leaving machine unattended. See Figure 2.7.

MOVE CONTROL TO “STOP”

2.2.7. ENGINE

1.Turn fuel shut off valve to the “ON” position. See Figure 2.3.

2.Insert key into ignition switch. See Figure 2.8.

3.Connect the power cord to the starter switch box on the engine, then plug the other end into 120 volt AC receptacle for U.S.A. or 230 Volt for Europe.

4.Move choke control to the choke, “ON” position. See Figure 2.8.

IMPORTANT: Stop the auger/impeller and wheel drive by releasing the auger/impeller and wheel drive control levers. Stop the engine by moving the engine speed control to the stop position or removing the key from the switch.

5.Move engine speed control to the “FAST” position. See Figure 2.8.

6.Push primer button three times to start a cold engine. NOTE: Do not use primer button to start warm engine.

7.Push the electric starter button. DO NOT hold button for more than 20 seconds to avoid damaging the starting motor. See Figure 2.8.

8.After engine starts, move the choke control to the no choke “OFF” position. Allow a brief warm-up until engine runs smooth.

9.Disconnect power cord from AC receptacle. Disconnect power cord from machine and remove cord from area where machine will be in operation.

REMOVE KEY

START

PLUG INTO

HERE

FIGURE 2.7

2.2STARTING, OPERATION & STOPPING (ELECTRIC START MODELS)

(Go to Page 9 for Recoil Start Models)

WARNING

DO NOT use an electrical extension cord that is damaged. A damaged electrical extension cord could cause a shock or fire. Thoroughly inspect electrical extension cord before using machine. If cord is damaged, do not use and do not operate machine. Replace damaged cord immediately. Contact your Snapper service dealer for assistance. To reduce the risk of electric shock, use only with an extension cord intended for outdoor use having

acord type: SW-A, SOW-A, STW-A, STOW-A, SJW- A, SJTW-A or SJTOW-A.

BUTTON

PUSH PRIMER

THREE TIMES

CONNECT

EXTENSION

CORD

 

MOVE ENGINE

 

SPEED CONTROL

 

TO “FAST”

MOVE

INSERT KEY

CHOKE TO

 

THE “ON”

 

POSITION

FIGURE 2.8

 

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Instruction No -3336 I.R /14/00 Model Number ExplanationModel Designation Series Designation Engine HP Auger Width Preparation Operational PrecautionsProtection for Children Maintenance and Storage Table of Contents Rabbit / Fast Turtle / Slow Neutral European Community Hearing Protection RequiredForward Reverse Ground Speed Control Year of Manufacture Safety Instructions to Prevent Injury Nomenclature IntroductionPRE-START Check List Minimum Gauge for Cord SetsGo to Page 11 for Electric Start Models Engine STARTING, Operation & Stopping Recoil Start ModelsEngaging Wheel Drive Discharge Chute and Deflector AdjustmentEngaging Auger STARTING, Operation & Stopping Electric Start Models Free Wheel Machine Stopping ENGINE, Auger & Wheel DriveCheck Wheel Drive Belt Service After First 5 Hours Check Auger Drive BeltGeneral Lubrication Gear CASE, Auger Shaft and Auger Bearing LubricationEngine Spark Plug Storage ProcedureMaintenance and Service Parts Annually END of Each SeasonAuger Belt Adjustment Idler Pulley Adjustment Auger and Drive Belt Adjustment Cable AdjustmentRecheck cable for proper extension Reinstall belt cover Repair & Adjustments Skid Shoe Adjustment Single Handle Control Adjustment Rubber Drive Tire Replacement Chute Crank AdjustmentUSE HRS Season Problem Probable Cause Corrective ActionService Performed Each 100Disclaimer of Warranty Year Limited WarrantyPage European TWO Stage Large Frame Snow Thrower Series
Related manuals
Manual 28 pages 34.11 Kb

E11305, E9265 specifications

Snapper E9265, 10305E, 8265, E10305E, and E11305 are part of an innovative line of electric snapper products designed to provide robust performance and versatility across various applications. These models represent the intersection of advanced technology and user-centric design, catering to both professionals and DIY enthusiasts.

One of the main features of these snapper models is their powerful motor. With high torque output, these devices can effortlessly tackle challenging materials, ensuring efficient operation in a range of conditions. This motor is engineered for durability and longevity, minimizing the need for maintenance while maximizing productivity.

The E9265 and E10305E feature cutting-edge brushless motor technology, which not only enhances performance but also increases energy efficiency. This feature is particularly beneficial for users who prioritize sustainability and seek to reduce their carbon footprint. The brushless motor extends the life of the tool and is quieter in operation compared to traditional brushed motors, making it ideal for use in residential areas or noise-sensitive environments.

Additionally, these models come equipped with advanced battery technology, featuring lithium-ion power packs that provide longer runtime and faster charging capabilities. Users can enjoy extended working periods without the anxiety of running out of power mid-task. The snapper line also integrates intelligent battery management systems that monitor charge levels and optimize power usage, prolonging battery life.

In terms of user experience, the Snapper E9265, 10305E, and other variants boast ergonomic designs that prioritize comfort and control. Anti-vibration handles reduce user fatigue during prolonged use, while variable speed settings allow for a customizable approach to different tasks. The lightweight construction of these tools enhances maneuverability, making them suitable for both heavy-duty applications and delicate work.

In addition to performance and comfort, safety features are a top priority in these models. Equipped with automatic shut-off functions and protective casing, the snapper tools ensure that users can operate them with confidence. This attention to safety doesn't compromise on efficiency, as these tools are built to deliver precise and powerful results.

Overall, the Snapper E9265, 10305E, 8265, E10305E, and E11305 embody a perfect blend of technology, performance, and user-friendly design. They are engineered to exceed the expectations of users across various fields, from construction to home improvement, making them a valuable addition to any toolkit. Whether you are a seasoned professional or a weekend warrior, Snapper offers a reliable solution that meets the demands of modern projects.
Top Page Image Contents