Snapper E9266, E11306 important safety instructions Single Handle Control Adjustment

Page 19

Section 4 - REPAIR & ADJUSTMENTS

4.1.6.SINGLE HANDLE CONTROL ADJUSTMENT

IMPORTANT: Standing in the operator’s position, the left handle bar lever is for wheel drive engagement and disengagement. The right handle bar lever is for auger/impeller engagement and disengagement. Hold both levers down to handle bar for engagement and release levers for disengagement. When both levers are pressed down to the handle bar at the same time, the operator can release the right hand lever and the right lever will remain engaged as long as the left hand lever is held down to handle bar. Release the left hand lever and both levers will disengage.

1.Hold the wheel drive control lever down against the handle. See Figure 4.9.

2.Check position of the cam lock. It must align with the adjusting line located on the cam lock bracket.

3.To adjust, loosen the nuts on the cable guide support bracket and move the bracket in or out until the cam lock aligns with the adjusting line. Retighten nuts.

4.Hold the wheel drive control lever down to the handle bar, at the same time press the auger/impeller control lever down to the handle bar and hold in position.

5.Check the position of the cable ferrule in relation to the cam lock. The ferrule must be located 1/16” (.060) above the hook of the cam lock. To adjust, loosen the three nuts that secure the cam lock bracket. Slide bracket up or down until correct measurement is achieved. Retighten nuts securely. See Figure 4.9.

 

TRACTION

 

HOLD DOWN

 

 

 

 

 

 

CLUTCH

 

 

 

 

CONTROL LEVER

BLOWER CLUTCH

 

 

 

 

 

 

 

 

CONTROL LEVER

 

 

(L.H. SIDE)

DISCHARGE

 

 

CABLE

 

CHUTE

 

 

 

REMOTE DEFLECTOR

(R.H. SIDE)

FERRULE

 

CONTROL

 

 

 

 

CONTROL (“T”

 

 

 

 

HANDLE)

 

 

 

 

 

 

.060

 

 

 

CABLE

(1/16”)

 

 

 

 

 

CABLE GUIDE

CAM LOCK

 

 

 

BRACKET

 

 

 

SUPPORT BRACKET

CAM LOCK

 

 

 

 

 

 

 

 

 

 

UP

 

 

“OUT”

“IN”

 

 

 

 

 

 

 

 

 

DOWN

CAM LOCK

CABLE

 

 

 

HOOK

ADJUSTING LINE (ON BRACKET)

FIGURE 4.9

19

Image 19
Contents Model Designation Series Designation Engine HP Auger Width Model Number ExplanationInstruction No -4243 I.R /15/01 Protection for Children Operational PrecautionsPreparation Maintenance and Storage Table of Contents Forward Reverse Ground Speed Control European Community Hearing Protection RequiredRabbit / Fast Turtle / Slow Neutral Sound Power Level Year of Manufacture Safety Instructions to Prevent InjuryNomenclature IntroductionPRE-START Check List Minimum Gauge for Cord SetsGo to Page 11 for Electric Start Models Engine STARTING, Operation & Stopping Recoil Start ModelsEngaging Auger Discharge Chute and Deflector AdjustmentEngaging Wheel Drive STARTING, Operation & Stopping Electric Start Models Free Wheel Machine Stopping ENGINE, Auger & Wheel DriveCheck Wheel Drive Belt Service After First 5 Hours Check Auger Drive BeltGeneral Lubrication Gear CASE, Auger Shaft and Auger Bearing LubricationEngine Spark Plug Storage ProcedureMaintenance and Service Parts Annually END of Each SeasonAuger Belt Adjustment Idler Pulley Adjustment Auger and Drive Belt Adjustment Cable AdjustmentRecheck cable for proper extension Reinstall belt cover Repair & Adjustments Skid Shoe Adjustment Single Handle Control Adjustment Rubber Drive Tire Replacement Chute Crank AdjustmentUSE HRS Season Problem Probable Cause Corrective ActionService Performed Each 100Disclaimer of Warranty Year Limited WarrantyPage European TWO Stage Large Frame Snow Thrower Series