|
|
|
| Troubleshooting | |
|
|
|
|
|
|
PROBLEM |
| POSSIBLE CAUSE |
| REMEDY |
|
Auger rotates, but snow is not | 1. Chute deflector too low. | 1. | Adjust deflector as necessary. |
| |
thrown far enough |
|
|
|
|
|
2. | Engine speed too slow. | 2. | Set speed to full throttle. |
| |
|
| ||||
|
|
|
|
|
|
| 3. | Ground speed too fast. | 3. | Use slower speed selector setting. |
|
|
|
|
|
|
|
| 4. | Snowthrower discharge chute | 4. | STOP engine and REMOVE the |
|
|
| clogged. |
| key. DISCONNECT the spark plug |
|
|
|
|
| wire. Clear auger using |
|
|
|
|
| tool. See warning in SAFETY |
|
|
|
|
| RULES. |
|
| 5. | Auger belt loose or worn. | 5. | Check auger drive belt adjustment |
|
|
|
|
|
| |
Poor traction | 1. Tires slipping. | 1. | Check tire pressure and tread. |
| |
|
|
|
|
| |
Auger does not stop when auger | 1. | 1. | Release BOTH auger engage |
| |
lever is released |
|
|
| Control AND |
|
|
|
|
| to stop auger. |
|
| 2. | Auger clutch rod too tight or bent. | 2. | Loosen or straighten clutch rod. |
|
|
|
|
|
|
|
| 3. | Auger drive belt out of adjustment. | 3. | Adjust auger belt. |
|
|
|
|
|
|
|
| 4. | Auger belt guide out of adjustment. | 4. | Adjust auger belt guide. |
|
|
|
|
|
| |
Snowthrower does not stop when | 1. Traction drive clutch rod bent or too | 1. | Loosen rod to remove slack or |
| |
drive lever is released |
| tight. |
| replace. See adjustment procedure. |
|
|
|
|
|
|
|
| 1. | Traction drive clutch rod loose. | 1. | Tighten to remove slack. See |
|
|
|
|
| adjustment procedure. |
|
|
|
|
|
|
|
| 2. | Drive belt loose, broken, or | 2. | Replace drive belt. |
|
|
| stretched. |
|
|
|
|
|
|
|
|
|
| 3. | Drive roller chain damaged. | 3. | Replace chain. |
|
|
|
|
|
|
|
| 4. | Traction lock pins in | 4. | Change traction lock pins to INNER |
|
|
| position (OUTER hole). |
| hole to engage traction drive. |
|
|
|
|
|
|
|
| 5. | Friction disc worn. | 5. | Replace disc (see your dealer). |
|
|
|
|
|
| |
|
|
|
|
| |
Discharge control is difficult to | 1. Gearing needs lubrication | 1. | Oil or grease as required. |
| |
operate. |
|
|
|
|
|
2. | Worm gear not adjusted properly. | 2. | Adjust worm gear. See adjustment |
| |
|
| ||||
|
|
|
| procedure. |
|
|
|
|
|
|
|
| 3. | Control rod gears misaligned. | 3. | Adjust gear bracket. See adjust- |
|
|
|
|
| ment procedure. |
|
|
|
|
|
| |
Snowthrower veers to one side. | 1. Tire pressure not equal. | 1. | Check tire pressure. |
| |
|
|
|
|
|
|
| 2. | One wheel is set in | 2. | Make certain the left traction lock |
|
|
| mode. (Traction Lock Pin is in the |
| pin is in the INNER holes (to |
|
|
| OUTER hole). |
| engage traction drive). |
|
|
|
|
|
| |
Excessive vibration. | 1. Loose parts or damaged auger. | 1. | STOP engine and REMOVE the |
| |
|
|
|
| key. DISCONNECT the spark plug |
|
|
|
|
| wire. Tighten all hardware. Replace |
|
|
|
|
| auger if necessary. If vibration con- |
|
|
|
|
| tinues, see your dealer. |
|
|
|
|
|
| |
Drive fails to move snowthrower | 1. Traction drive out of adjustment. | 1. | Readjust drive, or shift speed selec- |
| |
at slow speeds. |
|
|
| tor setting up one speed faster. |
|
|
|
|
|
| |
Speed selector difficult to move or | 1. Hex shaft needs lubrication. | 1. | Lubricate hex shaft with |
| |
frozen in place. |
|
|
| thetic motor oil (see Maintenance). |
|
|
|
|
|
|
|
21