Snapper 860 manual Troubleshooting, Adjustment, & Service

Page 21

Troubleshooting, Adjustment, & Service

TROUBLESHOOTING

This section provides troubleshooting and service instructions. Locate the problem and check the possible cause/remedy in the order listed.

Also, refer to the engine manufacturer’s Owner’s Manual for additional information.

For problems not covered here, contact your local deal- er.

WARNING

Before performing any adjustment or service to snowthrower, stop the engine and wait for moving parts to stop. Remove the key. To prevent accidental starting, disconnect the spark plug wire and fasten away from the plug.

PROBLEM		POSSIBLE CAUSE		REMEDY

Engine fails to start.	1.	Key is OFF.	1.	Push key in to the ON position.
	2.	Failure to prime cold engine	2.	Press Primer Button twice and restart.
	3.	Fuel valve is in CLOSED position.	3.	Turn valve to OPEN position.
	4.	Out of fuel.	4.	Fill fuel tank.
	5.	Choke OFF - cold engine.	5.	Turn choke to ON, set throttle to
				FAST.
	6.	Engine flooded.	6.	Turn choke to OFF; try starting.
	7.	Spark plug not sparking.	7.	Check gap. Gap plug, clean elec-
				trode, or replace plug as necessary.
	8.	Water in fuel, or old fuel.	8.	Drain tank (Dispose of fuel at an
				authorized hazardous waste facility).
				Fill with fresh fuel.

Engine starts hard or runs poorly.	1.	Fuel mixture too rich.	1.	Move choke to OFF position.
	2.	Carburetor adjusted incorrectly.	2.	See your dealer for adjustments.
	3.	Spark plug faulty, fouled, or gapped	3.	Clean and gap, or replace.
		improperly.
	4.	Fuel cap vent is blocked.	4.	Clear vent.

Auger does not rotate.	1.	Auger control not engaged.	1.	Engage auger control.
	2.	Foreign matter blocking auger.	2. STOP engine and REMOVE the key.
				DISCONNECT the spark plug wire.
				Clear auger using clean-out tool. See
				warning in SAFETY RULES.
			3.	Tighten to remove slack. See auger
	3.	Auger drive clutch cable slack.		clutch cable adjustment.
			4.	Check auger drive belt adjustment.
	4.	Auger drive belt slipping.	5.	Replace belt.
	5.	Broken belt.	6.	Replace shear pin.
	6.	Shear pin broken.

20

Image 21

Contents Models OPERATOR’S ManualTable of Contents Safety Rules & Information Children Safety RulesPage Identification Numbers CE Identification TAG MarkingsNorth American / CE Models CE Models only General Safety DecalsNorth American Model Decals CE Model DecalsCE Safety Icons & Compliance Specs ALL Models Tecumseh Models Briggs & Stratton Models Features, Controls, & OperationControl Locations Features & ControlsStarting Controls Engine ControlsUnits with Optional Electric Start Manual StartAuger Control Ground Speed ControlsDeflector Controls Scraper HeightChecks Before Each START-UP OperationStarting the Engine Clearing a Clogged Discharge Chute Operating the SnowthrowerGround Speed Selector Engine SpeedScraper BAR & Skid Shoes DeflectorAfter Each USE FREE-WHEELING Traction Drive LockMaintenance Schedule Checking Tire PressureCheck Auger Gear Case Lubrication Lubrication MaintenanceStorage Lubricating the Auger Shaft & AssemblyLubrication Check / Lubricate FREE-HAND Linkage StorageTroubleshooting Troubleshooting, Adjustment, & ServiceTroubleshooting Traction Drive Clutch Cable Adjustment AdjustmentsInitial Adjustment Run-In AdjustmentPinion Gear Adjustment Manual Discharge Chute Control Linkage AdjustmentDrive Belt Adjustment Auger Drive Clutch Cable AdjustmentAdjusting Auger Drive Belt Checking Auger Belt & Belt Guide AdjustmentsDrive Belt Replacement Adjustments & ServiceAdjusting Auger Belt Guide Traction Drive Belt ReplacementAuger Drive Belt Replacement ServiceShear PIN Replacement Roller Chain ReplacementCE Compliance Specifications DimensionsEngine ChassisReplacement Parts Maintenance ItemsTechnical Manuals