Snapper 8246, 9266, 9266E, E9266, 11306, E11306 Problem Probable Cause Corrective Action, 100

Page 19

TROUBLESHOOTING

PROBLEM

 

PROBABLE CAUSE

 

CORRECTIVE ACTION

 

 

 

 

Engine Will Not Start

1. Fuel tank empty.

1.

Fill fuel tank with fresh fuel/oil mix.

 

 

 

 

Using Recoil Starter

2. Engine needs choking and priming.

2.

Move choke control to “CHOKE” position. Push

 

 

 

 

primer bulb three times.

 

3.

Spark plug wire disconnected.

3.

Place spark plug wire onto spark plug.

 

 

 

 

 

 

4.

Fuel shut off valve closed.

4.

Move fuel shut off valve to the on position.

 

 

 

Engine Will Not Start

1. Power extension cord not plugged into machine or

1. Plug power extension cord into machine & into 120

Using Electric Starter

 

120 Volt outlet for U.S.A. or 230 Volt for Europe.

 

Volt outlet for U.S.A. or 230 Volt for Europe.

 

2.

Power extension cord damaged.

2.

Discard damaged power extension cord.

 

 

 

 

 

 

3.

Starter switch damaged or faulty.

3.

Replace starter switch.

 

 

 

 

Engine Stalls or Stops

1. Water, debris or stale fuel in fuel system.

1.

Drain and clean fuel system.

 

 

 

 

After Running

2. Choke control in the “CHOKE” position.

2.

Move choke control to “OFF” position.

 

 

 

 

 

 

3.

Fuel tank empty.

3.

Fill with fuel to proper level.

 

 

 

 

 

 

4.

Air intake clogged with snow or debris.

4.

Unclog air intake.

 

 

 

 

 

 

5.

Spark plug defective or gap set improperly.

5.

Service spark plug.

 

 

 

 

Engine Loses Power

1. Engine lubrication oil level is low.

1.

Add oil to the engine to full level.

 

 

 

 

 

 

2.

Spark plug faulty.

2.

Service spark plug.

 

3.

Water, debris or stale fuel in fuel system.

3.

Drain and clean fuel system.

 

 

 

 

Excessive Vibration

1. Damaged, out of balance or bent auger.

1.

Service auger.

 

 

 

 

 

 

2.

Loose engine or auger/impeller components.

2.

Service and tighten loose components.

 

 

 

 

 

 

3.

Bent or loose Idler pulley.

3.

Tighten or replace pulley.

 

 

 

 

 

 

4.

Cracked, severed or frayed belt.

4.

Replace belt.

 

 

 

Poor Snow

1. Clogged discharge chute.

1. Stop engine and unclog discharge chute.

Discharging

2. Damaged or bent auger/impeller or components.

2. Service auger/impeller or components.

 

3. Cracked, severed or frayed belt.

3. Replace belt.

 

 

 

 

4. Belt tension out of adjustment.

4. Adjust belt tension.

 

 

 

 

5. Insufficient lubrication in auger bearings.

5. Lubricate all bearings as specified in manuals.

 

 

 

 

 

SERVICE SCHEDULE

ITEM

SERVICE PERFORMED

REF.

EACH

5

25

50

100

EACH

 

 

 

USE

HRS

HRS

HRS

HRS

SEASON

Spark Plug

Replace

Engine Manual

 

 

 

 

X

 

 

 

 

 

 

 

 

 

 

Engine Oil

Check Oil Level

Engine Manual

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Initial Oil Change

Engine Manual

 

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Periodic Oil Change

Engine Manual

 

 

X

 

 

 

 

 

 

 

 

 

 

 

 

Air Filter

Clean or Replace

Engine Manual

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Engine Cooling

Clean Shroud & Fins

Engine Manual

 

 

 

 

X

 

System

 

 

 

 

 

 

 

 

Drive Belts

Check For Wear, Tension

Page 11, 13-

 

 

X

X

 

X

 

and Adjustments

15

 

 

 

 

 

 

Auger &

Check For Damage,

Page 11

X

 

 

 

 

X

Impeller

Lubrication, Stop Time

 

 

 

 

 

 

 

Tires

Check Air Pressure

Page 6

X

 

 

 

 

 

19

Image 19
Contents Engine HP Electric Start Auger Width Series Designation Model Number ExplanationManual No -5394 I.R /3/03 Protection for Children Operational PrecautionsPreparation Safe Handling of Gasoline Maintenance and StorageDo not refuel the machine indoors Table of Contents Nomenclature IntroductionPRE-START Check List Minimum Gauge for Cord SetsEngine STARTING, Operation & Stopping Recoil Start ModelsEngaging Auger Discharge Chute and Deflector AdjustmentEngaging Wheel Drive STARTING, Operation & Stopping Electric Start Models Free Wheel Machine Stopping ENGINE, Auger & Wheel DriveCheck Wheel Drive Belt Service After First 5 Hours Check Auger Drive BeltGeneral Lubrication Gear CASE, Auger Shaft and Auger Bearing LubricationEngine Spark Plug Storage ProcedureMaintenance and Service Parts Annually END of Each SeasonAuger Belt Idler Pulley Adjustment Auger and Wheel Drive Cable AdjustmentRecheck cable for proper extension 3/8 Reinstall belt cover Repair & Adjustments Skid Shoe Adjustment Single Handle Control Adjustment Rubber Drive Tire Replacement Chute Crank AdjustmentUSE HRS Season Problem Probable Cause Corrective ActionService Performed Each 100Disclaimer of Warranty Year Limited WarrantySnapper Product Registration Form Page Page Page Instruction No -5394 I.R /3/03 TWO Stage Large Frame Snow Thrower Series