Poulan 415180 owner manual Engine, Cleaning

Page 14

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYDischarge chute control lever used to change the di Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting HOW to USE Your Snow Thrower StoppingTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Storage OtherTroubleshooting Service Notes AIG plugr1 KEY Part Description 07Chute-knob2 414280 Knob, Lever Repair Parts Snow Thrower - Model NO. PR8527ES Handles 412677 Repair Parts Snow Thrower - Model NO. PR8527ES Drive 401732 Page KEY Part Description Page 415475 415180 415181Limited Warranty

415180 specifications

The Poulan 415180 is a powerful and versatile chainsaw designed for homeowners and professional users alike. With its combination of robust power, innovative technologies, and user-friendly features, it stands out in the competitive market of outdoor power equipment.

At the heart of the Poulan 415180 is a dependable 18-inch bar and chain that delivers exceptional cutting performance. The 42cc engine is engineered to provide sufficient torque for cutting through tough wood, making it suitable for a variety of tasks ranging from trimming branches to felling small trees. Its lightweight design allows for easy maneuverability, reducing user fatigue during extended use.

One of the standout features of the Poulan 415180 is its automatic oiler system. This technology ensures that the chain is consistently lubricated during operation, reducing wear and prolonging the life of both the chain and bar. The oiler can be adjusted to the specific demands of the task, allowing users to optimize the lubrication based on the type of wood being cut or the duration of use.

Starting up the chainsaw is made hassle-free with the innovative easy-start system. This feature minimizes the effort required to start the engine, providing a smooth and quick ignition with minimal pulling force. Additionally, the chainsaw is equipped with a primer bulb, ensuring that fuel reaches the carburetor more efficiently, which further improves starting performance in various weather conditions.

Safety is a key consideration in the design of the Poulan 415180. It includes features such as a chain brake, which can be activated to stop the chain almost instantly in the event of a kickback. The sturdy handle offers a comfortable grip and enhanced control, allowing for safe operation during cutting tasks.

The Poulan 415180 also emphasizes user comfort and convenience. Its lightweight construction, along with an anti-vibration system, helps to minimize fatigue and discomfort, making it an ideal choice for long periods of use.

Overall, the Poulan 415180 is a reliable chainsaw that merges power with practicality. It caters to the needs of both casual users and seasoned professionals, making it an excellent investment for anyone looking to tackle outdoor cutting projects with ease and efficiency.
Top Page Image Contents