Poulan 414659 owner manual To Remove Wheels See Fig

Page 16

SERVICE AND ADJUSTMENTS

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt

must be fully seated in pulley groove when bringing

 

the snow thrower together.

16

12.Install the two (2) hex bolts and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lockwasher and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

 

AUGER

SQUARE

 

BELT

HOLE

 

 

CLUTCHING

 

IDLER ARM

 

BRACKET

 

 

AUGER PULLEY

 

 

 

BOLT

FRAME

AUGER

 

HOUSING

 

FIG. 21

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 22

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYRecoil auxiliary starter handle used for starting Meets A.N.S.I. Safety RequirementsDischarge chute control lever used to change the di HOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Scraper BAR Before Starting the EngineTo Start Engine Before Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Cleaning EngineTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector To Remove Wheels See Fig Storage OtherTroubleshooting Service Notes AIG plugr1 KEY Part Description Page 414280 Knob, Lever Repair Parts Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Drive Repair Parts Snow Thrower Model PP10530ES Drive 07Chassis-chain-cord-Tec3 KEY Part Description Repair Parts Wheels / Decals Wheels / Decals Limited Warranty

414659 specifications

The Poulan 414659 is a powerful and versatile chainsaw designed for homeowners and professionals alike. This reliable tool offers an impressive combination of features and technologies, making it a popular choice for various cutting tasks, from trimming branches to felling trees.

One of the standout features of the Poulan 414659 is its robust engine. With a high-performance 42cc motor, this chainsaw delivers ample power to tackle demanding projects while remaining lightweight and easy to maneuver. This balance of power and weight ensures that users can handle extended periods of cutting without experiencing excessive fatigue.

The chainsaw is equipped with a 16-inch bar and chain, providing a considerable cutting capacity. This length is ideal for handling medium-sized trees and larger branches. Furthermore, the Oregon chain is designed for smooth cutting performance, allowing for clean cuts and reducing the risk of kickback.

Ease of use is a key characteristic of the Poulan 414659. The chainsaw features an adjustable automatic oiling system that ensures the chain remains properly lubricated during operation. This feature not only prolongs the life of the chain but also contributes to efficient cutting. Additionally, the tool's easy-access air filter and spark plug make maintenance a breeze, allowing users to keep the chainsaw in peak condition with minimal effort.

Safety is another priority for Poulan. The chainsaw comes equipped with a chain brake, which quickly stops the chain in case of kickback. This feature, combined with a low-vibration design, enhances user safety and comfort, making it easier to control the saw during operation.

The Poulan 414659 also incorporates a soft-grip handle for improved comfort and better grip, ensuring users have a solid hold while cutting. The lightweight design, coupled with a well-balanced body, makes it easy to maneuver in various cutting positions.

In summary, the Poulan 414659 is a feature-rich chainsaw that combines power, ease of use, and safety. With its 42cc engine, 16-inch bar, automatic lubrication system, and safety features, this chainsaw is an excellent tool for anyone looking to tackle outdoor cutting tasks efficiently. Whether you're a seasoned professional or a first-time user, the Poulan 414659 offers the reliability and performance needed to get the job done effectively.
Top Page Image Contents