Poulan 414659 owner manual Storage, Other

Page 17

SERVICE AND ADJUSTMENTS

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYDischarge chute control lever used to change the di Meets A.N.S.I. Safety RequirementsRecoil auxiliary starter handle used for starting Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Other StorageTroubleshooting Service Notes AIG plugr1 KEY Part Description Page 414280 Knob, Lever Repair Parts Repair Parts Snow Thrower Model PP10530ES Handles Repair Parts Drive Repair Parts Snow Thrower Model PP10530ES Drive 07Chassis-chain-cord-Tec3 KEY Part Description Repair Parts Wheels / Decals Wheels / Decals Limited Warranty

414659 specifications

The Poulan 414659 is a powerful and versatile chainsaw designed for homeowners and professionals alike. This reliable tool offers an impressive combination of features and technologies, making it a popular choice for various cutting tasks, from trimming branches to felling trees.

One of the standout features of the Poulan 414659 is its robust engine. With a high-performance 42cc motor, this chainsaw delivers ample power to tackle demanding projects while remaining lightweight and easy to maneuver. This balance of power and weight ensures that users can handle extended periods of cutting without experiencing excessive fatigue.

The chainsaw is equipped with a 16-inch bar and chain, providing a considerable cutting capacity. This length is ideal for handling medium-sized trees and larger branches. Furthermore, the Oregon chain is designed for smooth cutting performance, allowing for clean cuts and reducing the risk of kickback.

Ease of use is a key characteristic of the Poulan 414659. The chainsaw features an adjustable automatic oiling system that ensures the chain remains properly lubricated during operation. This feature not only prolongs the life of the chain but also contributes to efficient cutting. Additionally, the tool's easy-access air filter and spark plug make maintenance a breeze, allowing users to keep the chainsaw in peak condition with minimal effort.

Safety is another priority for Poulan. The chainsaw comes equipped with a chain brake, which quickly stops the chain in case of kickback. This feature, combined with a low-vibration design, enhances user safety and comfort, making it easier to control the saw during operation.

The Poulan 414659 also incorporates a soft-grip handle for improved comfort and better grip, ensuring users have a solid hold while cutting. The lightweight design, coupled with a well-balanced body, makes it easy to maneuver in various cutting positions.

In summary, the Poulan 414659 is a feature-rich chainsaw that combines power, ease of use, and safety. With its 42cc engine, 16-inch bar, automatic lubrication system, and safety features, this chainsaw is an excellent tool for anyone looking to tackle outdoor cutting tasks efficiently. Whether you're a seasoned professional or a first-time user, the Poulan 414659 offers the reliability and performance needed to get the job done effectively.
Top Page Image Contents