Sears 536.884811 Cean Adjustme TS, To Adjust Skids Height, To Adjust Scraper BAR, To Adjust Chute

Page 17

S CEAN ADJUSTME TS

i

CAUTION: ALWAYS DISCONNECT THE SPARK PLUG WIRE AND TIE BACK AWAY FROM THE PLUG BEFORE MAKING ANY ADJUSTMENTS OR REPAIRS.

i i

TO ADJUST SKIDS HEIGHT

This snow thrower is equipped with two height adjust-

ment skids, located on the outside of the auger housing These skids elevate the front of the snow thrower°

For normal hard surfaces, adjust the skids as follows:

eMake sure the snow thrower is on a hard, level surface and the weight transfer system lever is released See page 12.

oPlace extra shear bolts supplied (found in parts

bag) under each end of the scraper bar near but not under the skids

@Loosen the skid mounting nuts (See Fig 20) and push the skids down until they touch the ground. Retighten the mounting nuts

For rocky or uneven surfaces, raise the front of the snow thrower by moving the skids down This will help prevent rocks and other debris from being picked up and thrown by the auger°

NOTE: tfthe skids are at the maximum height, the weight transfer system will not work

TO ADJUST SCRAPER BAR

After considerable use, the metal scraper bar wilt have a definite wear pattern. The scraperbar in conjunction with the skids should always be adjusted to allow 1/8" be- tween the scraper bar and the sidewalk or area to be cleaned.

®Position the snow thrower on a level surface

oLoosen the carriage bolts and nuts securing the scraper bar to the auger housing_

oAdjust the scraper bar to the proper position

oTighten the carriage bolts and nuts, making su rethat the scraper bar is parallel with the working surface.

oAfter extended operation, the scraper bar may be re- versed, if the scraper bar must be replaced due to wear, remove the carriage bolts and nuts and install a new scraper bar

SKID MOUNTING NUTS

HEIGHT ADJUST SKID

/

/1//i

ill

ill

illl

/i

Jl

i

ii

ii i

M_

FIG. 20

CAUTION: BE CERTAIN TO MAINTAIN PROPER GROUND CLEARANCE FOR

YOUR PARTICULAR AREA TO BE CLEARED. OBJECTS SUCH AS GRAVEL, ROCKS OR OTHER DEBRIS, IF STRUCK BY THE IMPELLER, MAY BE THROWN WITH SUFFICIENT FORCE TO CAUSE

PERSONAL INJURY, PROPERTY DAM- AGE OR DAMAGE TO THE SNOW

THROWER.

i

ill

i

i

llllll///

//

i i

i

TO ADJUST CHUTE

CRANK ASSEMBLY

If you cannot rotate the chute crank fully to the left and to the right, you need to adjust the chute crank (See Fig 21)

eLoosen both 1/2" nuts on the crank adjusting rod (using 3/4" wrenches)

oRotate the adjusting rod in or out to allow about t/8"

clearance between the notch in the flange and the outer diameter of the worm

•Once this clearance is set, tighten the nuts

NOTE: Be sure the crank does not touch the side of the engine or the cover will be scratched

I

FLATWASHER 1

1/2 INCH

CRANK ADJUSTING ROD

WORM

FIG_ 21

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Crafi Smah Before USE Safety RulesFuel Safety Safe Storage J8C Valve Clearance Maintenance AG ReementCustomer Responsibilities Index ContentsParts BAG Contents AssemblyContents of Shipping Carton Tools Required for Assembly To SET the Skid Height HOW to SET UP Your Snow ThrowerTo Remove Snow Thrower Flatwasher To Install the Upper Handle and Crank AssemblyInch WormAS LY To Install the Shifter LeverIs thrown WeightTo Control Snow Discharge HOW to USE Your Snow ThrowerTo Move Forward and Backward To Throw SnowBefore Starting the Engine To USE Weight Transfer SystemFILL/ADD OIL Handling or Storing ITTo Stop Engine OP AtioTo Start Engine Frozen StarterOperation General Recommendations TE AnceSnow Thrower After First USEEngine AddmarkLubricaiion Spark PlugTo Adjust Skids Height Cean Adjustme TSTo Adjust Scraper BAR To Adjust ChuteCables ServiceTo ADJ UST Belts Lever Mustbein Full ForwardposiDOORS, Away from Fire or Flame To Replace BeltsAuger Drive Belt To Adjust the Friction Wheel Service and Adjustmen TSTo Adjust the Belt Guides Track Drive BeltAway from Fire or Flame Service AN AdjustTo Replace Auger Shear Bolt To Adjust TrackTo Adjust or Replace Spark Plug To Adjust CarburetorTo Adjust To ReplaceAway from Open Flame Snow ThrowerOther Lubrication Chart Service Records ScheduleService Dates Correction Trouble Shooting PointsTrouble Cause Inotes Craftsman 23 Snow Thrower Part Name CraftsmanLocknut I12 InoLockwasher91 !8 37 55 9013 78\NO, PARTNO. Part Name Craftsman 23 Snow Thrower203O 308048 Auger Housing Assembly Re air Parts Chute REFoGear BOX Repair Parts590647 Rewind Starter noNumbershere MODELand Serial162 34443A 96 *26756 98 33673A 100 101 102141 142 143 144 145 146 147 148 149 150 160 3408O Carburetor no a Inotes Give the Following Information Product Snow Thrower When Ordering Repair PARTS, AlwaysModel Number Engine Model Number Part Number Part Description

536.884811 specifications

The Sears 536.884811 is a well-regarded model of the sewing machine that has gained popularity among hobbyists and professionals alike. Renowned for its robust construction and user-friendly design, this sewing machine encapsulates both functionality and reliability.

One of the standout features of the Sears 536.884811 is its versatility. Equipped with a variety of built-in stitch patterns, it accommodates a wide range of sewing tasks from basic repairs to creative projects. The machine includes essential stitches such as straight, zigzag, and decorative options, making it suitable for different fabrics and styles.

The machine is powered by a reliable motor, ensuring consistent performance even with thicker materials. This is particularly valuable for users who work with a diverse assortment of textiles, from delicate silk to denim. Its adjustable presser foot pressure is a beneficial feature, allowing users to customize the sewing experience to match the fabric being used.

One of the noteworthy technologies integrated into the Sears 536.884811 is the automatic needle threader, which simplifies the threading process and is especially advantageous for those with visual impairments or dexterity issues. This machine also boasts an easy bobbin system, minimizing downtime spent on setup and maximizing productivity.

Ergonomics play a vital role in the design of the Sears 536.884811. Its layout includes a clear and intuitive control interface that enables even novice users to navigate settings easily. Additionally, the work area is well-lit, ensuring optimal visibility while sewing, which is crucial for precision in detailed work.

Storage and portability are other key characteristics that make the Sears 536.884811 a favorite among sewers. The machine often comes with built-in compartments that neatly organize accessories and tools, making it easy to keep everything in order. Moreover, its lightweight design facilitates transport, making it an excellent choice for classes or travel.

In summary, the Sears 536.884811 exemplifies a harmonious blend of classic sewing machine engineering and modern conveniences. With its range of stitch options, ease of use features, and thoughtful design, it serves as an ideal choice for anyone looking to elevate their sewing projects, whether they are beginners or more experienced crafters.
Top Page Image Contents