Sears 536.884811 owner manual Snow Thrower, Other, Away from Open Flame

Page 24

ii ii.

......................CAUT'iON:NEVE"STORETHEENGINE

WITH FUEL IN THE TANK INDOORS OR IN AN ENCLOSED, POORLY VENTILATED AREAWHERE FUEL FUMES MAY REACH AN OPEN FLAME, SPARK OR PILOT LIGHT AS ON A FURNACE,. WATER ttEATER, CLOTHES DRYER, ETC,.

NOTE: Immediately prepare your snow thrower for stor- age at the end of the season or'if the unit will not be used for 30 days or more,.

SNOW THROWER

•Thoroughly clean the snow thrower'.

•Lubricate all lubrication points (see the Mainte- nance section, pages 15 -16).

•Be sure that all nuts, bolts and screws are securely fastened. Inspect all visible moving parts for dam- age, breakage and wear° Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightlybefore painting,

•Cover the bare metal parts of the blower housing auger and the impeller with r_Jstpreventative, such as sprayable lubricant.

NOTE: A yearly checkup o rtuneup by a SEARS Service Center is a good way to insure that your snow thrower will provide maximum performance for the next season.,

ENGINE

IMPORTANT: ITIS IMPORTANTTO PREVENTGUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS THE CARBURETOR, FUEL FILTER, FUEL HOSE OR TANK DURING STORAGE.. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OFAN ENGINE WHILE IN STORAGE.

Drain the gasoline from the fuel tank by removing the fuel line. Drain the fuel and reinstall the fuel lined

"'i

_

C '_T'ioN:DRAIN FUEL iNTO

......... i

Ii,

 

APPROVEDCONTAINEROUTDOOBS,I

!

AWAY FROM OPEN FLAME.

............. i

E

BOWL DRAIN

FIG. 39

•Start the engine and run at SLOW (idle) speed until the engine stops from lack of fueL

•Drain the carburetor by pressing upward on the

bowl drain (See Fig_39), located below the carbure- tor cover_

NOTE: Fuel stabilizer (such as STA-BIL)is an accept- able alternative in minimizing the formation of fuel gum

deposits dudng storage Add stabilizer to gasoline in fuel tank or storage container, Always follow the mix ratio

found on stabilizer container_ Run engine at least 10 minutes after adding stabilizer to allow the stabilizer'to reach the carburetor,.Do not drain the gas tank and car- buretor if using fuel stabilizer_

Remove the spark plug and squirt one (1) ounce of engine oil into the cylinder. Pult the recoil starter rope slowly, allowing the piston to coat the internal engine parts.. Install an old spark plug. This prevents fouling a new plug with the preservative used to lubricate the internal parts of the engine_ Close the choke and plug the muffler opening°

OTHER

•If possibJe, store your snow thrower indoors and cover it to give protection from dust and dirt.

•Ifthe machine mustbe storedoutdoors, block upthe snow thrower to be sure the entire machine isoff the ground.

•Cover the snow thrower with a suitable protective cover that does not retain moisture, Do not use plastic.,

IMPORTANT: NEVER COVER SNOW THROWER WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Crafi Smah Safety Rules Fuel SafetyBefore USE Safe Storage Maintenance AG Reement Customer ResponsibilitiesJ8C Valve Clearance Contents IndexAssembly Contents of Shipping Carton Tools Required for AssemblyParts BAG Contents HOW to SET UP Your Snow Thrower To Remove Snow ThrowerTo SET the Skid Height To Install the Upper Handle and Crank Assembly FlatwasherInch WormTo Install the Shifter Lever AS LYWeight Is thrownHOW to USE Your Snow Thrower To Control Snow DischargeTo Move Forward and Backward To Throw SnowTo USE Weight Transfer System Before Starting the EngineFILL/ADD OIL Handling or Storing ITOP Atio To Stop EngineTo Start Engine Frozen StarterOperation TE Ance General RecommendationsSnow Thrower After First USEAddmark EngineLubricaiion Spark PlugCean Adjustme TS To Adjust Skids HeightTo Adjust Scraper BAR To Adjust ChuteService CablesTo ADJ UST Belts Lever Mustbein Full ForwardposiTo Replace Belts Auger Drive BeltDOORS, Away from Fire or Flame Service and Adjustmen TS To Adjust the Friction WheelTo Adjust the Belt Guides Track Drive BeltService AN Adjust Away from Fire or FlameTo Adjust Track To Replace Auger Shear BoltTo Adjust Carburetor To Adjust or Replace Spark PlugTo Adjust To ReplaceSnow Thrower OtherAway from Open Flame Service Records Schedule Service DatesLubrication Chart Trouble Shooting Points Trouble CauseCorrection Inotes Craftsman 23 Snow Thrower Craftsman Part NameLocknut I12 InoLockwasher78\ 91 !8 37 55 9013Craftsman 23 Snow Thrower NO, PARTNO. Part Name203O 308048 Auger Housing Assembly Re air Parts REFo ChuteRepair Parts Gear BOXRewind Starter no 590647MODELand Serial Numbershere96 *26756 98 33673A 100 101 102 141 142 143 144 145 146 147 148 149 150 160 3408O162 34443A Carburetor no a Inotes When Ordering Repair PARTS, Always Give the Following Information Product Snow ThrowerModel Number Engine Model Number Part Number Part Description

536.884811 specifications

The Sears 536.884811 is a well-regarded model of the sewing machine that has gained popularity among hobbyists and professionals alike. Renowned for its robust construction and user-friendly design, this sewing machine encapsulates both functionality and reliability.

One of the standout features of the Sears 536.884811 is its versatility. Equipped with a variety of built-in stitch patterns, it accommodates a wide range of sewing tasks from basic repairs to creative projects. The machine includes essential stitches such as straight, zigzag, and decorative options, making it suitable for different fabrics and styles.

The machine is powered by a reliable motor, ensuring consistent performance even with thicker materials. This is particularly valuable for users who work with a diverse assortment of textiles, from delicate silk to denim. Its adjustable presser foot pressure is a beneficial feature, allowing users to customize the sewing experience to match the fabric being used.

One of the noteworthy technologies integrated into the Sears 536.884811 is the automatic needle threader, which simplifies the threading process and is especially advantageous for those with visual impairments or dexterity issues. This machine also boasts an easy bobbin system, minimizing downtime spent on setup and maximizing productivity.

Ergonomics play a vital role in the design of the Sears 536.884811. Its layout includes a clear and intuitive control interface that enables even novice users to navigate settings easily. Additionally, the work area is well-lit, ensuring optimal visibility while sewing, which is crucial for precision in detailed work.

Storage and portability are other key characteristics that make the Sears 536.884811 a favorite among sewers. The machine often comes with built-in compartments that neatly organize accessories and tools, making it easy to keep everything in order. Moreover, its lightweight design facilitates transport, making it an excellent choice for classes or travel.

In summary, the Sears 536.884811 exemplifies a harmonious blend of classic sewing machine engineering and modern conveniences. With its range of stitch options, ease of use features, and thoughtful design, it serves as an ideal choice for anyone looking to elevate their sewing projects, whether they are beginners or more experienced crafters.
Top Page Image Contents