Sears 536.884811 owner manual To Adjust Carburetor, To Adjust or Replace Spark Plug, To Replace

Page 23

S RVICE AN ADJUST E TS

TO ADJUST CARBURETOR

The carburetor (See Fig. 37) has been pre-set at the factory and readjustment should not be necessary.. However, if the carburetor does need to be adjusted, proceed as follows:

®Close the high speed adjusting screw by hand..

®Do not overtighteno

o Then open it 1-1/4 to 1-1/2 turns°

®Close the id)e adjusting screw by hand, Do not overtighten.

oThen open it 1-1/4 to 1-1/2 turns_

®Start the engine and let it warm up,

oSet the throttle control to FAST. Adjust the high speed adjusting screw in until the engine speed or sound alters° Adjust the screw out until the engine

speed sound alters. Note the difference between the two limits and set the screw in the middle of the

range..

eSet the throttle control to SLOW,. Adjust the idle adjusting screw in until the engine speed drops, then adjust the screw out until the engine speed drops. Note the difference between the two limits and set the screw in the middle of the range..

®If the engine tends to stall under load or not accel- erate from low speed to high speed properly, adjust the high speed screw out in 1/8 turn increments until the problem is resolved°

®Let the engine run undisturbed for 30 seconds between each setting to allow the engine to react to the previous adjustments.

_IDLE

ADJUSTING SCREW

_:j- (Close finger tight only)

(Close finger tight only)

i i Hl=,,Hll ,l= ,

FIG. 37

TO ADJUST:

eClean the spark plug by carefully scraping elec- trodes (do not sand blast or use a wire brush)_

oBe sure the spark plug is clean and free of foreign matedaL Check electrodes gap (See Fig. 38) with a wire feeler gauge and reset the gap to 030 inch if necessary_

.030 GAP

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHlCH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS.

IF YOU THINK THE ENGINE GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOU R NEAREST SEARS SERVICE CENTER, WHICH HAS THE PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS,.

TO ADJUST OR REPLACE

THE SPARK PLUG

FIG. 38

TO REPLACE:

eIf you need a new spark plug, use only the proper replacement spark plug.

eSet the gap to _030(See Fig 38).

oBefore installing the spark plug, coat its threads lightly with graphite grease to insure easy removal

•Tighten the plug firmly into the engine,

•Ifa torque wrench is available, to rque the plug to 18 to 23 ft - Ibs

If you have difficulty starting you r snowthrower, you may need to adjust or replace the spark plug. Follow the instructions below.

Replace the spark plug it electrodes are pitted or burned or if the porcelain is cracked

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Crafi Smah Before USE Safety RulesFuel Safety Safe Storage J8C Valve Clearance Maintenance AG ReementCustomer Responsibilities Index ContentsParts BAG Contents AssemblyContents of Shipping Carton Tools Required for Assembly To SET the Skid Height HOW to SET UP Your Snow ThrowerTo Remove Snow Thrower Worm To Install the Upper Handle and Crank AssemblyFlatwasher InchAS LY To Install the Shifter LeverIs thrown WeightTo Throw Snow HOW to USE Your Snow ThrowerTo Control Snow Discharge To Move Forward and BackwardHandling or Storing IT To USE Weight Transfer SystemBefore Starting the Engine FILL/ADD OILFrozen Starter OP AtioTo Stop Engine To Start EngineOperation After First USE TE AnceGeneral Recommendations Snow ThrowerSpark Plug AddmarkEngine LubricaiionTo Adjust Chute Cean Adjustme TSTo Adjust Skids Height To Adjust Scraper BARLever Mustbein Full Forwardposi ServiceCables To ADJ UST BeltsDOORS, Away from Fire or Flame To Replace BeltsAuger Drive Belt Track Drive Belt Service and Adjustmen TSTo Adjust the Friction Wheel To Adjust the Belt GuidesAway from Fire or Flame Service AN AdjustTo Replace Auger Shear Bolt To Adjust TrackTo Replace To Adjust CarburetorTo Adjust or Replace Spark Plug To AdjustAway from Open Flame Snow ThrowerOther Lubrication Chart Service Records ScheduleService Dates Correction Trouble Shooting PointsTrouble Cause Inotes Craftsman 23 Snow Thrower I12 InoLockwasher CraftsmanPart Name Locknut91 !8 37 55 9013 78\NO, PARTNO. Part Name Craftsman 23 Snow Thrower203O 308048 Auger Housing Assembly Re air Parts Chute REFoGear BOX Repair Parts590647 Rewind Starter noNumbershere MODELand Serial162 34443A 96 *26756 98 33673A 100 101 102141 142 143 144 145 146 147 148 149 150 160 3408O Carburetor no a Inotes Engine Model Number Part Number Part Description When Ordering Repair PARTS, AlwaysGive the Following Information Product Snow Thrower Model Number

536.884811 specifications

The Sears 536.884811 is a well-regarded model of the sewing machine that has gained popularity among hobbyists and professionals alike. Renowned for its robust construction and user-friendly design, this sewing machine encapsulates both functionality and reliability.

One of the standout features of the Sears 536.884811 is its versatility. Equipped with a variety of built-in stitch patterns, it accommodates a wide range of sewing tasks from basic repairs to creative projects. The machine includes essential stitches such as straight, zigzag, and decorative options, making it suitable for different fabrics and styles.

The machine is powered by a reliable motor, ensuring consistent performance even with thicker materials. This is particularly valuable for users who work with a diverse assortment of textiles, from delicate silk to denim. Its adjustable presser foot pressure is a beneficial feature, allowing users to customize the sewing experience to match the fabric being used.

One of the noteworthy technologies integrated into the Sears 536.884811 is the automatic needle threader, which simplifies the threading process and is especially advantageous for those with visual impairments or dexterity issues. This machine also boasts an easy bobbin system, minimizing downtime spent on setup and maximizing productivity.

Ergonomics play a vital role in the design of the Sears 536.884811. Its layout includes a clear and intuitive control interface that enables even novice users to navigate settings easily. Additionally, the work area is well-lit, ensuring optimal visibility while sewing, which is crucial for precision in detailed work.

Storage and portability are other key characteristics that make the Sears 536.884811 a favorite among sewers. The machine often comes with built-in compartments that neatly organize accessories and tools, making it easy to keep everything in order. Moreover, its lightweight design facilitates transport, making it an excellent choice for classes or travel.

In summary, the Sears 536.884811 exemplifies a harmonious blend of classic sewing machine engineering and modern conveniences. With its range of stitch options, ease of use features, and thoughtful design, it serves as an ideal choice for anyone looking to elevate their sewing projects, whether they are beginners or more experienced crafters.
Top Page Image Contents