Troy-Bilt 4510 warranty Service

Page 22

5.Holding the friction wheel assembly, slide the hex shaft out of the right side of the frame. The spacer on the left side of the hex shaft will fall and the sprocket should remain hanging lose in the chain.

6.Lift the friction wheel assembly out between the axle shaft and the drive shaft assemblies.

7.Remove four screws securing the friction wheel to the hub assembly (refer to Figure 7-11). Discard old friction wheel.

Figure 7-11

8.Reassemble the new friction wheel onto the hub assembly, tightening the four screws in rotation and with equal force. It is important to assemble the friction wheel symmetrically for proper functioning. Refer to

Figure 7-11.

9.Reposition the friction wheel assembly in the snow thrower frame. Insert the pin from the shift arm assembly into the friction wheel assembly and hold assembly in position. Refer to Figure 7-12.

10.Slide the hex shaft through the right side of the frame toward the left side and through the friction wheel assembly.

NOTE: If the sprocket fell from the snow thrower chain while removing the hex shaft, position the hex hub of the sprocket toward the friction wheel and place the sprocket in the chain.

11.After making certain that the chain is on both the large and the small sprocket, align the hex shaft with the hex hub of the small sprocket, and slide the shaft through the sprocket.

12.Slide the spacer onto the end of the hex shaft.

13.Align the bearing on the right end of the hex shaft with the hole in the right side of the frame, then push the hex shaft to the left into position in the frame.

Figure 7-12

14.Slide the bearing onto the left end of the hex shaft and press into the hole on the left side the frame.

15.Place the belleville washer (rounded side toward head) onto the hex screw removed earlier, and insert the screw into the threaded hole of the hex shaft.

16.Gradually tighten the hex screw to fully seat the bearings in each side of the frame and to secure the hex shaft.

17.Position the frame cover on the bottom of the frame and secure with the self-tapping screws. Pivot the snow thrower down to its normal operating position.

22

Section 7— Service

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Operator’s Manual Thank You Table of ContentsTo The Owner Record Product InformationCalifornia Proposition Training Important Safe Operation PracticesPreparation Operation Safe Handling of GasolineDo not modify engine Maintenance & StorageSpark Arrestor Safety Symbols SymbolContents of Carton Assembly & Set-UpAssembly Chute Assembly Chute Directional ControlAdjustments Set-UpAdjusting Drive and Auger Controls Testing Drive Control & Shift LeverGas & Oil Fill-Up Choke Control Controls and FeaturesShift Lever Ignition KeyPrimer Bulb Electric Starter SwitchChute Assembly Oil FillChute Directional Control Chute Clean-Out ToolTwo-Way Chute Control Wheel Steering ControlsStopping The Engine OperationStarting The Engine Electric StarterTo Engage Augers Replacing Shear PinsTo Engage Drive Operating TipsMaintenance Maintenance & AdjustmentsLubrication Auger Shaft Chute Bracket AdjustmentGear Case AugersAuger Control Drive ControlTire Pressure Auger Belt Replacement ServiceBelt Replacement Belt Removal PreparationPulley Slot Drive Belt Replacement Changing Friction WheelService Short-Term Storage Off-Season StorageLong-Term Storage Troubleshooting Problem Cause RemedyReplacement Parts ComponentPage Page MANUFACTURER’S Limited Warranty for

4510 specifications

The Troy-Bilt 4510 is a versatile and robust walk-behind mower designed to cater to both residential and small commercial lawn care needs. Known for its durability and efficiency, this mower has several features and technologies that make it a reliable choice for homeowners and professionals alike.

One of the standout features of the Troy-Bilt 4510 is its powerful engine. It is equipped with a robust 160cc engine that offers exceptional performance in various cutting conditions. The engine provides ample power to tackle thick grass and uneven terrain, ensuring a clean and even cut every time. The easy-start mechanism simplifies the ignition process, allowing users to get to mowing quickly without any hassle.

The 4510 also boasts a self-propulsion system with variable speed control, giving users the ability to adjust the pace of the mower according to their preferences and the mowing conditions. This feature is particularly beneficial when navigating tight corners or dealing with steep inclines, providing excellent maneuverability without sacrificing power.

Cutting height adjustment is another key characteristic of the Troy-Bilt 4510. With a simple lever adjustment, users can choose from multiple cutting height settings, allowing for personalized grass length options to suit different seasons or lawn types. This flexibility in cutting height ensures an aesthetically pleasing lawn year-round.

The mower's deck is designed for efficiency, featuring a 21-inch cutting width that allows it to cover more ground in less time while still providing precise cuts. The deck is often made from durable steel, ensuring longevity and resistance to wear and tear. Additionally, the Troy-Bilt 4510 features a mulch, bag, and side discharge capability, offering versatility in grass clipping management.

For user comfort, the mower comes with ergonomically designed handles that reduce fatigue during extended mowing sessions. The folding handle design makes storage easy, allowing the mower to occupy less space when not in use.

In summary, the Troy-Bilt 4510 is a feature-rich walk-behind mower that emphasizes power, ease of use, and adaptability. With its reliable engine, self-propulsion system, adjustable cutting height, and multiple clipping options, it is well-suited for homeowners who take pride in their lawns, as well as for professionals seeking efficient landscaping solutions. Whether tackling residential lawns or small commercial projects, the Troy-Bilt 4510 delivers performance and quality that users have come to expect from the Troy-Bilt brand.
Top Page Image Contents